Duplo DP-A100 II Скачать руководство пользователя страница 12

10

 Optional equipment should be installed after 

the machine itself has been installed and test-
run to check that it functions normally. For the 
procedure for installing optional equipment, 
see the Installation Manual supplied with it.

8. If Options Are Installed

U5-Y1320

2017.05

2. How to adjust ink amount of the knob on 

the operator’s side: Adjust it from the gap 
between the outer frame and the drum.

3. When printed too dark or too light on the     

operator’s side:

 Too dark: turn the knob in the 

 direction (3 steps)

 Too light: turn the knob in the 

+

 direction (3 steps)

 Ink adjusting knob on the operator’s side 

Too dark

Too  light

Never loosen the set screw. 

 (standard position) 

 

 Ink adjusting knob on the rear side 

Too light

Too dark

Never loosen the 

set screw.

 (standard position)  

4. When printed too dark or too light on the rear 

side:

 Too dark: turn the knob in the 

 direction (3 steps)

 Too light: turn the knob in the 

+

 direction (3 steps)

6. After the adjustment, move the cover 

displaced in step 1.2 back to its original 
position and secure it with the screw. 

7. Return the drum rotated in step 1.1 back to 

its original position. (The stopper 

fi

 ts in the 

groove of the drum.)

5. When printed too dark or too light on the 

entire surface: Adjust the above steps 3 and 
4 at the same time.

 There are seven steps, standard and 

±3 steps to adjust image density. When 
adjusting image density, print dozen of 
sheets to stabilize the density every time 
you change it by every step. Repeat the 
above steps until you get desired print 
density.

IMPORTANT

 Do not rotate the drum in the opposite 

direction of the arrow. Ink may over

fl

 ow.

IMPORTANT

Содержание DP-A100 II













Отзывы: