background image

  D U N I W A Y  S T O C K R O O M  C O R P .

W W W . D U N I W A Y . C O M

27 of 28

Warranty

Terranova products of Duniway Stockroom Corp. are warranted to be free of defects in 
material and workmanship for a period of one year from the date of shipment. At our 
option, we will repair or replace products which prove to be defective during the war-
ranty period. Liability under this warranty is limited to repair or replacement of the 
defective items. Shipping damage is excluded from the scope of this warranty. Gauge 
tubes of all types are excluded from this warranty.

Terranova products are warranted not to fail to execute programming instructions due 
to defects in materials and workmanship. If Duniway Stockroom receives notice of such 
defects during the warranty period. Duniway Stockroom will repair or replace firmware 
that does not execute its programming instruction due to such defects. Duniway Stock-
room does not warrant that the operation of the firmware or hardware will be uninter-
rupted or error-free.

If this product is returned to Duniway Stockroom for warranty service, Buyer will pre-
pay shipping charges and will pay all duties and taxes for products returned to Duniway 
Stockroom. Duniway Stockroom will pay for return of products to Buyer, except for 
products returned to a Buyer from a country other than the United States.

LIMITATION OF WARRANTY: The foregoing warranty does not apply to the defects 
resulting from:

1. Improper or inadequate maintenance by Buyer;
2. Buyer-supplied interfacing;
3. Unauthorized modification or misuse;
4. Operation outside of the environmental specifications of the product; or
5. Improper site preparation and maintenance.

THE WARRANTY SET FORTH ABOVE IS EXCLUSIVE AND NO OTHER WARRANTY, 
WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED. DUNIWAY STOCK-
ROOM DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE.

EXCLUSIVE REMEDIES: The remedies provided herein are Buyer’s sole and exclusive 
remedies. In no event will Duniway Stockroom be liable for direct, indirect, special, 
incidental, or consequential damages, including loss of profits, whether based on con-
tract, tort, or any other legal theory.

X

TELEPHONE: 650-969-8811     TOLL-FREE (U.S. only): 800-446-8811     FAX: 650-965-0764     EMAIL: [email protected]

www.duniway.com

Содержание Terranova 906A





























Отзывы: