background image

Page 16 of 16

Diagram 9

Once the grilles are fitted the front plate can be put on. The corner tabs can be distorted in transit hence they

may need to be straightened. Insert the tabs at the corners into the slots in the side plates then push the top

of the access panel home and lock it into place using the two locks and key provided.

MAINTENANCE

Every 3-6 months the front panel should be removed, the grilles removed (in the reverse of the method on

the previous pages) and the casing inspected for dust and debris. The casing and grilles should be cleaned

using a soft brush, damp cloth and warm soapy water. Any dust and debris should be vacuumed from the

casing,  and  the  finned  element.  Care  should  be  taken  not  to  damage  the  finned  element  a  soft  brush

attachment should be used.

WARNING

Some internal components may have sharp edges.  Care must be taken when servicing this product and it is

recommended that protective gloves are worn.

SPARES/SERVICE

Spare parts/service – Please contact our office, contact information shown below.

Manufacturer reserves the right to change any product specification without notice.

Dunham-Bush Ltd, Downley Road, Havant, Hants, PO9 2JD

Sales and Technical Support

Spare Parts and Service

Tel:  023 9247 7700     Fax:  023 9245 3601

Tel:  023 9247 7700     Fax:  023 9245 3601

Email:  [email protected]

Email:  [email protected]

Содержание System LST

















Отзывы: