manualshive.com logo in svg

Duerkopp Adler 4181-3, Инструкция по эксплуатации, Страница: 3 / 35

Поделиться
Скачать
Duerkopp Adler 4181-3 Скачать руководство пользователя страница 3

3.6.8.2 Forward, rearward and side setting

3.6.8.3 Setting the gear clearance

3.6.8.4 Replacement of the top roller

3.7

Setting the presser foot lift   

........................................................................................................................................... 19

3.8

Bobbin winder  ....

......................................................................................................................................................... 20

3.8.1 Description

3.8.2 Setting the bobbin winder stop

3.8.3 Setting the friction gear

3.9

Safety clutch   

................................................................................................................................................................ 21

3.9.1 Description

3.9.2 Setting the disengaging moment

3.10 Indented belt transmission   

.......................................................................................................................................... 21

3.10.1 Setting the tensioning roller of the indented belt

3.10.2 Replacing the indented belt

3.11 V-belt, motor - head  

..................................................................................................................................................... 22

3.11.1 Tensioning

3.11.2 Replacing the V-Belt

3.12 Lubrication 

.................................................................................................................................................................... 23

3.12.1 Description

3.12.2 Refilling oil

3.12.3 Multiple oil use

4. Thread trimming 

..................................................................................................................................................................... 24

4.1 Description of the trimming mechanism

4.2 Setting the pickup roller

4.3 Setting the cam

4.4 Setting the fork

4.5 Setting the moving knife

4.6 Setting the height of the fixed knife and of the retaining spring of the lower thread

4.7 Setting the fixed knife

4.8 Setting the retaining spring of the hook thread

4.9 Setting switching of the electromagnets

5. Material trimming   

.................................................................................................................................................................. 26

5.1 Description of the trimming mechanism

5.2 Mounting and dismantling the motor  - trimming drive

5.3 Setting the position of the material trimming knife

5.4 Setting the length of the trimming knife movement with regard to the stich length

5.5 Setting of the trimming switching on and off microswitch

5.6 Setting of the switching - on lever stop

5.7 Grinding the work trimmer knife

6. Lifting the top roller by electromagnet  

................................................................................................................................... 28

6.1 Description

6.2 Setting the electromagnet pin

6.3 Setting the electromagnet current

6.4 Assembly of the top roller lifting electromagnet

7. Backtacking using electromagnet 

........................................................................................................................................... 29

7.1 Description

7.2 Electromagnet height setting

7.3 Setting the position of push-buttons

7.4 Change of the function of push-buttons

8. Connecting the electric elements on the machine head  

......................................................................................................... 30

9. Drive, control panel, position sensor

    

................................................................................................................................... 30

10. Lighting   

.................................................................................................................................................................................. 30

10.1 Mounting on the machine head

10.2 Lamp replacement

11. Maintenance (table of operations)  

......................................................................................................................................... 31

12. Setting the machine according to the sewing category 

........................................................................................................... 32

12.1 Introduction

12.2 Table of setting the machine according to the sewing category

Содержание 4181-3




































Отзывы:

Нет отзывов