Ducane 13HPD-018-230 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 24

Ducane 13HPD-018-230 Скачать руководство пользователя страница 23

Page 23

13HPD SERIES

DEFROST THERMOSTAT SWITCH (S6)

The defrost thermostat as illustrated in figure 1 is located on the liquid line between the CTXV and the distributor. When
defrost thermostat senses 42°F (5.5°C) or cooler, the thermostat contacts close and send a signal to the defrost control to
start the defrost timing. It also terminates defrost when the liquid line warms up to 70°F (21°C).

Table 5. Defrost Control Inputs, Outputs and Configurable Settings

Control Loca-
tion

Control Label or
Description

Purpose

Function

P1

TEST

Test Mode

See Test Mode on page 22 for further details.

P1

30, 60, 90

Defrost Temperature
Termination (Jumper) Pins

The defrost control as illustrated in figure 20 has valid selections
which are: 30, 60, and 90°F (−1, 16 and 32°C). The shunt termination
pin is factory set at 50°F (10°C). If the temperature shunt is not
installed, the default termination temperature is 90°F (32°C).

P2

W1

24VAC Thermostat Input /
Output

24VAC input/output from indoor thermostat to indoor unit.

C

24VAC Common

24VAC common

L

Thermostat Service Light

Thermostat service light connection.

R

24VAC

24VAC

O

Thermostat Input

Reversing valve solenoid.

Y1

Thermostat Input

Controls the operation of the unit.

P5

DELAY

Delay Mode

The defrost control has a field−selectable delay to reduce occasional
sounds that may occur while the unit is cycling in and out of the defrost
mode. When a jumper is installed on the DELAY pins, the compressor
will be cycled off for 30 seconds going in and out of the defrost mode.
Units are shipped with jumper installed on DELAY pins.

NOTE − The 30 second off cycle is NOT functional when
jumpering the TEST pins on P1.

P6

TST, PS DF, C, R, O, Y1

Factory Test Connectors

Factory Use Only.

DS1

RED LED

Diagnostic LED

Valid states for defrost control’s two LEDs are OFF, ON and
FLASHING which indicate diagnostics conditions that are described
in table 4.

DS2

GREEN LED

FAN

TWO CONNECTORS

Condenser Fan Operation

These two connections provide power for the condenser fan.

O OUT

O OUT

24VAC output

24VAC output connection for reversing valve.

LO−PS

LO−PS

Low−Pressure Switch

Not Used.

DF

DF

Defrost Thermostat

Defrost thermostat connection points.

Y1 OUT

Y1 OUT

24VAC Common Output

24VAC common output, switched for enabling compressor contactor.

HS−PS

HS−PS

High−Pressure Switch
(Optional)

Not Used.

L

L

Service Light Output output

24VAC service light output.

24V

24V

24VAC output

Not Used.

«
...
21
22
23
24
»

Содержание 13HPD-018-230

























Отзывы:

Нет отзывов