Ducane 13HPD-018-230 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

Ducane 13HPD-018-230 Скачать руководство пользователя страница 16

Page 16

506695−01 11/10

Refer to the furnace or blower coil installation instructions
for additional wiring application diagrams and refer to unit
nameplate for minimum circuit ampacity and maximum
overcurrent protection size.

1. Install line voltage power supply to unit from a properly

sized disconnect switch.

2. Ground unit at unit disconnect switch or to an earth

ground.

NOTE − To facilitate conduit, a hole is provided in the
bottom of the control box. Connect conduit to the
control box using a proper conduit fitting.

NOTE − Units are approved for use only with copper
conductors. 24V, Class II circuit connections are
made in the low voltage junction box (see figure 12).

NOTE − A complete unit wiring diagram is located
inside the unit control box cover.

NOTE − For proper voltages, select thermostat wire
gauge per the following chart:

Wire run length

AWG #

Insulation type

less than 100’ (30m)

18

color−coded, temperature
rating 35

º

C minimum

more than 100’ (30m)

16

3. Install room thermostat (ordered separately) on an

inside wall approximately in the center of the

conditioned area and 5 feet (1.5 m) from the floor. It
should not be installed on an outside wall or where it
can be effected by sunlight, drafts or vibrations.

4. Install low voltage wiring from outdoor to indoor unit

and from thermostat to indoor unit (see figure 12).

R

C

W1

Y1

O

G

R

C

W1

W2

W3

G

REVERSING VALVE

THERMOSTAT

INDOOR

UNIT

R

C

W1

Y1

O

OUTDOOR

UNIT

POWER

COMMON

FIRST STAGE

AUXILIARY HEAT

INDOOR BLOWER

COMPRESSOR

(SOME CONNECTIONS MAY NOT APPLY. REFER
TO SPECIFIC THERMOSTAT AND INDOOR UNIT.)

FIRST STAGE

AUXILIARY HEAT

COMMON

POWER

HEAT PUMP WITH AIR HANDER

AND ELECTRIC HEAT

E

L

Figure 12. Typical Low Voltage Connections

«
...
14
15
16
17
18
...
»

Содержание 13HPD-018-230

























Отзывы:

Нет отзывов