background image

The sensor cable supplied with the motor can only be installed in one direction to the motor. Always make sure the wire is clean and not damaged. Never shorten the length of the wire, you can get optional length 
wires but altering them will cause the wire to fail. Please note the ESC markings and match the correct wires to the correct terminals on the motor.

There are 3 Power Wires that must be soldered to your motor. These are normally colour coded as Blue for Wire A, Yellow for wire B and Orange/Red for Wire C. Please note the ESC markings match the correct 
wires to the correct terminals on the motor.

 Install the motor in the model using M3 screws no longer than 8mm in length.

 Connect the power wires of the ESC making sure you match wire A with wire A, B with B and C with C. 

Motor Instruction Manual

Z5 Competition Brushless Motor

The Z5 brushless motor is a no compromise high performance sensored motor. It is designed to withstand extreme levels of use at the highest possible performance.
The motor works as a sensored unit and also sensorless without the sensor cable attached if your ESC runs sensorless. Please read the following information to maximize your performance from your purchase.

 Never leave the product unsupervised while it is switched on, in use or connected with a power source. If a defect occurs, it could set fire to the product or the surroundings.

 Avoid incorrect connections or connections with reversed polarity of the product.

 All wires and connections have to be well insulated. Short-circuits can possibly destroy the product.

 Never allow this product or other electronic components to come in contact with water, oil or fuels or other electroconductive liquids, as these could contain minerals, which are harmful for 

   electronic circuits. If this happens, stop the use of your product immediately and let it dry carefully.

 Avoid overloading the motor due to wrong or too long gear ratios. Different ESC’s have different built in timings, follow the ESC instructions.

 Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor can get damaged.

 Always wire up all the parts of the equipment carefully. If any of the connections come loose as a result of vibration, you could loose control over your model.

 Avoid soldering longer then 5 seconds per soldering joint when replacing the power wires to prevent possible damage to the product due to overheating of the components.

   Use a high power soldering station with at least 60W for soldering.

 Never allow the motor to get over 80 degrees Celsius (176 degrees Fareheit) as you may damage the motor and especially loose strength in your rotor.

 The manufacturer can not be held responsible for damages, which are a result of non-observance of the caution advices.

This is not a toy. Not suitable for children under 14 years. Keep the product out of the reach of children. Pay close attention to the following points, as they can destroy the product and void your warranty. 
Non-observance of these points can lead to property damage, personal and severe injuries!

Cautions

Installation & Connections

 If you are using a sensored ESC then connect the sensor wire to both the motor and ESC.

 Double check you have all the connections correct before use.

该产品不是玩具,不适合14岁以下的儿童使用。请将产品放在儿童不宜接触到的地方。请注意以下几点,因为它们可以毁坏产品且使您的产品无法保修。不遵守以下要点可能会导致财产损失及造成人
身伤害!

 

绝不能在产品处于通电状态时放在一边处理别的事情。如果出现问题,产品本身会造成起火并影响到周边设备。

 

避免连接错误或极性反接的情况发生。

 

确保所有电线和连接部绝缘良好,短路可能毁坏产品。

 

请不要让本产品或其他电子元件与水、油、燃料或其他导电液体接触,因为这些可能含有对电子电路有害的矿物质。如果发生以上情况,请立即停用您的产品,并小心进行干燥处理。

 

避免由于错误或齿比太大导致马达超载。不同的ESC的进角调节有所不同,请按照ESC指示操作。

 

齿轮未安装前提下禁止全油门操作,无负载情况下,高转速会损坏电机。

 

请务必仔细连接好各部件。若因连接松动造成车体震动,此时您有可能会失去对车子的控制。

 

当更换电源线时,避免焊接超过5秒以预防由于部件过热可能对产品造成的损害。使用至少60W功率的焊接配置进行焊接。

 

切勿使马达温度超过80摄氏度(176华氏度),高温将会毁坏马达并且会导致转子消磁。

 

在使用者不按照产品说明书进行操作,而造成产品毁坏的情况下,生产商不承担任何责任。

Z5竞赛级无刷马达是一款当之无愧的高性能有感车用马达,是基于高水平比赛而设计的。
该马达兼具有感无感功能,所以在无感的情况下也能很好的配合到电调的无感模式完成比赛。请阅读以下信息以便您更好的使用本产品。

(Z5竞赛级车用无刷马达)

马达需焊接三根电源线。这些电源线通常以颜色区分,蓝色作为A相,黄色作为B相,橙色或红色作为C相。请注意ESC标记,匹配正确的线连接到电机上的正确的端子。

随马达提供的感应线与马达连接时不能反插。务必确保感应线是干净的,未损坏的。切勿缩短感应线的长度,您可以选配不同长度的感应线,擅自改动感应线长度可能会导致感应线功能失效。
请注意ESC标记,匹配正确的线连接到电机上的正确的端子。

 

采用不长于8mm的 M3螺丝安装马达到模型上。

 

连接/焊接ESC的动力线,确保他们一一对应即: 电线A与A相匹配,电线B与B相匹配,电线C与C相匹配。

 

如果您要使用有感ESC,请将感应线两端分别连接在马达和ESC的接线口上。

 

使用前再次仔细检查所有连接的正确性。

Z 5

(注意事项)

(安装和连接)

The motor comes set to 30 degrees timing. Increasing the timing will increase the RPM of the motor whilst at the same time increasing temperatures and 
losing efficiency. Higher timing will require a shorter gear ratio. We recommend you start with this setting and adjust based on your needs from that position.

When setting your motor timing it is important to make sure your ESC is set correctly. Please follow your ESC instructions on how to do this. To check your 
motor temperatures during testing simply drive for 3 laps of the track, stop and use a temperature gun (74151) to make sure you are not too hot. If the 
motor is too hot then allow the motor to cool before trying it again.

You can alter the timing on the motor to change the powerband and characteristics of the motor for best and the most efficient performance. Neutral timing is 40 degrees with 10 degrees tuning either side. 30 
degrees timing on minimum setting (fully clockwise) to 50 degrees (fully anti-clockwise).

To adjust the timing simply loosen the 3 outer screws on the back of the motor and rotate the Sensor Back Cover, noting the lines on the motor and the mark on the cover.

Timing Adjustment

通过松动马达后盖的三颗螺丝来调节马达的进角,根据后盖上的刻度调节您所需要的进角角度,调节完成,记得扭紧后盖螺丝。

(进角调整)

马达默认设置30度进角(最小)。调大进角将增加马达的转速,同时马达的温度上升和效率降低。大进角需要配合到较高(较大)的齿比,我们建
议您基于以上建议开始设定马达的进角。

当设置您的马达进角时,请确保您的Esc设置正确,这一点很重要。请按照ESC说明书进行操作。测试马达的温度是很简单的,你只需沿赛道跑三
圈然后停下来用温度枪来确认马达是否过热。如果马达太热,您需等到马达冷却后方可再次测试。

您可以通过调整马达的进角改变动力输出区间和特性以达到最佳的性能。中位进角是40度,两侧有10度调节范围。最小进角30度(顺时针调节到底),最大进角50度(逆时针调节到底)。

ESC

A

B

C

A (Blue)

To RX

To Battery

To Fan

Switch

B (Yellow)

+ (Positive)

(Negative)

C (Orange)

Отзывы: