background image

Input Signal Connections

Low Level Input (RCA)

Low level (RCA) input signal is preferred for best performance. Typical trunk-

mount amplifier installations require a 17-20 foot RCA cable. Most trucks 

and under-seat applications require a 6-9 foot RCA cable. Using twisted pair 

construction RCA cables will minimize noise.

 

 

 

 

          High Level Input 

 

 

 

 

          (Speaker Wire)

High level inputs should only 

be used when RCA outputs are 

not available from the head unit. 

Connect the head unit speaker 

outputs to the high level input 

connector as shown below. The 

black wire (signal reference 

ground) may or may not require a 

connection to chassis ground 

- depending on your particular 

installation.

Low-Level Input

(RCA)

Speaker Connections

Connect speaker wires 

observing polarity. The 

minimum impedance load 

for the 

amplifiers is 2 ohms 

stereo and 4 ohms bridged. 

Use of loads lower than these 

is not recommended and may 

cause amplifier damage. The 

amplifiers can be wired for 

stereo, b

ridged or stereo/

bridged simultaneous 

operation.

Speakers  

(bridged)

Typical Bridged Wiring

(4 ohms minimum)

 

2 Speakers (stereo)

Typical Stereo Wiring

(2 ohms minimum)

 

L

R

Note:

 Do not use both low and high level inputs 

at the same time - connect only one or the other. 

8

INSTALLATION

Amplifier Connections

Содержание DA10004D















Отзывы: