background image

Do not release oils and fuel into the environment. Dispose of all oils and fuels through 
suitably certified outlets according to local regulations.

15. Disposal and Environmental Protection

Old appliances contain valuable materials that can 
be recycled; these should be sent for recycling. 
Batteries, oil, and similar substances must not enter the 
environment. Please dispose of your old appliances 
using appropriate collection systems.

Please do not release engine oil, fuel oil, diesel and 
petrol into the environment. Protect the ground and 
dispose of used oil in an environmentally-clean manner.

The packaging material 
can be recycled. Please do 
not throw the packaging 
material into household 
waste; please send it for 
recycling.

16

14. Troubleshooting

Symptom

Possible Cause

Remedy

Pump running normally 
but pressure low.

Pressure Regulator valve
Pump sucking air.

Check and adjust
Check water supply and
possible air ingress.

Nozzle badly worn

Check and/or replace

Worn piston packing

Seek professional advice

Fluctuating pressure

Blocked water filter

Check filter, clean or
replace if necessary.

Pump sucking air

Check integrity of suction
hose and connections.

Pressure low after a long 
period of normal use.

Nozzle badly worn

Check and/or replace

Pump noisy.

Pump sucking air

Check integrity of suction
hose and connections.

Excessive temperature of

Reduce temperature to 

liquid in pump

below 60ºC, do not allow
pump to idle for long periods.

Blocked water filter

Check filter, clean or
replace if necessary.

Worn bearing or valves

Seek professional advice

Presence of water in oil.

Ingress through breathers

Replace oil, do not wash 
engine or pump

Worn oil seals

Seek professional advice

Water dripping from under pump.

Worn piston packing

Seek professional advice

Oil dripping from 
pump/gearbox/engine.

Worn oil seal

Seek professional advice

Excessive vibration in 

Water supply low

Check adequacy of water 

lance/delivery line.

supply. Ensure suction 
filter is below water level.

Ingress of air into suction 

Check integrity of suction

line

hose and connections.

Irregular functioning of 

Seek professional advice

valves

Check filter, clean or
replace if necessary.

Blocked water filter

Содержание TBE15500DHE





















Отзывы: