CEILING OR END MOUNT INSTALLATION
WALL MOUNT INSTALLATION
TRANSFORMER
CONNECTOR
TO CHARGER (J1)
WIRE HARNESS
FROM HEATER
ASSY 7 PIN
CONNECTOR
TO GROUND
CONNECTION
ON FRAME
277
120
COM
TO JUNCTION
BOX
3 PIN PUSH
CONNECTOR (QTY 4)
SUPPLIED PIGTAIL LEADS
PREWIRED AT FACTORY
BLK
WHT
GREEN (GROUND)
PIGTAIL LEAD
RED
PIGTAIL LEAD
BLK
PIGTAIL LEAD
WHT
PIGTAIL LEAD
ORG
BLK
WHT
GREEN
WIRING DIAGRAM
10. REMOVE CHEVRON(S) IF REQUIRED.
DRIVE CHEVRON TOWARDS BACK
OF STENCIL BY TAPPING AROUND
THE ENTIRE PERIMITER FROM
FRONTSIDE OF STENCIL FOR CLEAN
BREAKOUT.
2. REMOVE APPROPRIATE KNOCKOUTS
FOR WALLBOX SCREWS.
4. ATTACH PRE-TINNED PIGTAIL LEADS
PROVIDED TO AC INPUT CONDUCTORS.
3. IF USING CONDUIT, REMOVE
PIPE PLUG, OTHERWISE
REMOVE CENTER KNOCKOUT.
5. REMOVE ADHESIVE BACKING FROM
MOUNTING GASKET & APPLY TO
EXIT BACKPLATE.
6. ROUTE PIGTAIL LEADS THRU CENTER
KNOCKOUT IN BACKPLATE & MOUNT
SIGN TO WALLBOX.
7. ATTACH ADHESIVE WIRING SADDLE
AND ROUTE WIRES INTO CHANNEL.
(SEE DETAIL 1)
8. ROUTE PIGTAILS THRU LIGHTBOX
(SEE WIRING DIAGRAM & DETAIL 1)
AND MAKE PROPER CONNECTIONS USING
PUSH CONNECTORS.
9. ATTACH 2-PIN BATTERY CONNECTOR
TO PC BOARD AS SHOWN. (SEE DETAIL 1)
11. CONFIRM ALL WIRING IS DRESSED
PROPERLY, HANG STENCIL & DIFFUSER
ONTO FRAME PINS
.(SEE DETAIL 1)
12. SEAT COVER & SECURELY TIGHTEN
COVER SCREWS. (SEE DETAIL 3)
PIGTAIL ROUTING FROM CEILING CANOPY
TO PUSH CONNECTORS
LEADS TO PASS THRU
SLOT IN LIGHT BOX
(WALL MTG)
LEADS TO BE SECURED
BY WIRE SADDLE (PROVIDED)
(WALL MTG)
PUSH CONNECTORS
(QTY 4) SEE WIRING
DIAGRAM FOR
CONNECTION
INSTRUCTIONS
PIGTAIL ROUTING FROM SIDE MOUNTED
CANOPY TO PUSH CONNECTORS
PIGTAIL ROUTING FROM CENTER KO ON
BACKPLATE TO PUSH CONNECTORS
2-PIN BATTERY CONNECTION
AC
TRANSFORMER
120VAC-CONNECT BLACK & WHITE LEADS.
277VAC-CONNECT RED & WHITE LEADS.
13. REMOVE CHEVRON(S) IF
REQUIRED. DRIVE
CHEVRON TOWARDS
BACK OF STENCIL BY
TAPPING AROUND THE
ENTIRE CHEVRON
PERIMITER
FROM FRONTSIDE OF
STENCIL FOR CLEAN
BREAKOUT.
3. ATTACH PRE-TINNED PIGTAIL LEADS
PROVIDED TO AC INPUT CONDUCTORS.
2. REMOVE PIPE PLUG.
4. FEED LEADS THROUGH CENTER OF
UNIVERSAL MOUNTING PLATE AND
ATTACH PLATE TO ELECTRICAL BOX.
5. AFFIX NUT TO PIPE NIPPLE. SLIP
THROUGH CANOPY CENTER HOLE AND
AFFIX SECOND NUT ONTO PIPE NIPPLE
AND TIGHTEN. THIS WILL LOCK PIPE
NIPPLE TO CANOPY. (SEE DETAIL)
7. ROUTE PIGTAILS THRU GASKET & CANOPY.
6. REMOVE ADHESIVE BACKING FROM
MOUNTING GASKET & APPLY TO
CANOPY.
8. WITH SCREWS SUPPLIED (QTY 2) SECURE
CANOPY TO UNIVERSAL MOUNTING PLATE
9. REMOVE ADHESIVE BACKING FROM FRAME
GASKET, ROUTE PIGTAILS THROUGH GASKET
& APPLY TO CANOPY. (SEE DETAIL 2)
10. ROUTE PIGTAILS THROUGH EXIT FRAME
AND PIPE NIPPLE NUT. AFFIX NUT TO
PIPE NIPPLE AND TIGHTEN TO SECURE
EXIT FRAME. (SEE DETAIL 2)
11. ROUTE PIGTAILS TO PUSH CONNECTORS.
(SEE WIRING DIAGRAM & DETAIL 1)
12. ATTACH 2-PIN BATTERY CONNECTOR
TO PC BOARD AS SHOWN. (SEE DETAIL 1)
14. CONFIRM ALL WIRING IS DRESSED PROPERLY,
HANG STENCIL/DIFFUSER ONTO FRAME PINS.
(SEE DETAIL 1)
15. SEAT COVER(S) & SECURELY TIGHTEN
COVER(S) SCREWS. (SEE DETAIL 3)
DETAIL 2
CANOPY GASKET
COMPRESSION STOPS
CANOPY
ANTI-ROTATION
RIBS
NOTE: PIPE NIPPLE NUT INSIDE EXIT FRAME SHALL BE TIGHTENED
SO THAT CANOPY GASKET COMPRESSION STOPS SEAT
AGAINST EXIT FRAME. THIS INSURES THAT THE GASKET IS
COMPRESSED PROPERLY TO SEAL SIGN & SIGN WILL BE
SECURE AGAINST ROTATING ON CANOPY.
GASKET
NOTE: CLEAR POLYCARBONATE COVER(S) ARE SIMILAR TO THE
CANOPY IN THAT THEY ALSO HAVE COMPRESSION STOPS
(COVER HAS THEM AT ALL 4 CORNERS) THAT SEAT
AGAINST EXIT FRAME. THIS INSURES GASKET WILL BE
COMPRESSED PROPERLY TO SEAL SIGN.
DETAIL 3
SEAT COVER TO FRAME
DETAIL 1
FRAME PINS
CENTER KNOCKOUT
1. USE SPANNER SCREW BIT (PROVIDED)
TO REMOVE & TIGHTEN ALL SPANNER
SCREWS.
1. USE SPANNER SCREW BIT (PROVIDED)
TO REMOVE & TIGHTEN ALL SPANNER
SCREWS.
CANOPY PIPE NIPPLE
NUT
APPROX. 3/16"
NOTE: FOR END MOUNTED SINGLE FACED SIGNS, THE
BACKPLATE AND CLEAR COVER WITH STENCIL/DIFFUSER
CAN BE SWAPPED FOR MOUNTING VERSATILITY
A
DETAIL A
IMPORTANT: TO WEATHERPROOF FOR OUTDOOR INSTALLATION,
BE SURE TO SEAL ALL OPENINGS — MOUNTING, CONDUIT, ETC.
IMPORTANT: TO WEATHERPROOF FOR OUTDOOR INSTALLATION,
BE SURE TO SEAL ALL OPENINGS — MOUNTING, CONDUIT, ETC.
93021644
93021643
93021641
93021640
93021638
93021646
93021645
