WebDT 182
ENGLISH
2
3
ENGLISH
THE WebDT 182
Powering ON and OFF
The Power Bu
tt
on is located in the front of the WebDT 182. The Power Bu
tt
on may be con
fi
gured to
func
ti
on di
ff
erently depending on the power op
ti
ons of the opera
ti
ng system. In general, to turn the
WebDT 182 on, push and release the Power Bu
tt
on on the front bezel. The adjacent power LED will
be lit (blue) and the corresponding interface will be displayed on the display monitor.
To turn o
ff
the device, again depending on so
ft
ware opera
ti
ng system, push and release the Power
Bu
tt
on or use a so
ft
ware shutdown interface. In the event of system lockup, the Power Bu
tt
on may
be used to perform a reset on the device. To do that, push and hold the Power Bu
tt
on for at least 4
seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power Bu
tt
on
again will restart the device.
Device Ports
The WebDT 182 features an op
ti
mal set of I/O ports while preserving the compact size of the
system. The HDMI connector, Network (10/100/1000 BaseT Ethernet), and Power ports are
supplemented by a set of four USB 2.0 and two Audio ports. Through its USB ports, the WebDT 182
supports a wide range of USB-based peripherals. These peripherals are applicable in providing the
means for so
ft
ware installa
ti
on, applica
ti
on storage, data storage, and system so
ft
ware recovery
and updates.
Memory and Storage
The WebDT 182 may be available in 8GB of
fl
ash memory, SSD or HDD storage con
fi
gura
ti
ons.
Depending on base so
ft
ware con
fi
gura
ti
on, the user may use the internal memory of the WebDT
182 for user’s installed so
ft
ware and storage. The user may also supplement storage space with
USB-based peripherals such as
fl
ash disks, disk drives, etc. RAM capacity is up to 2GB.
VESA Moun
ti
ng Bracket Installa
ti
on Guide for WebDT182
The WebDT 182 package includes a VESA-compliant moun
ti
ng bracket (1) which mounts the
WebDT182 (2) onto a VESA-compa
ti
ble monitor or display.
NOTE: The VESA Moun
ti
ng Bracket is compa
ti
ble with most displays and monitors that support the VESA standard.
Precau
ti
ons
Always exercise care when opera
ti
ng and handling the WebDT 182.
•
Never disassemble any por
ti
on of the enclosure. It will void any product warranty on the WebDT
•
182.
Do not use any AC/DC adapter other than the one provided with the device or acquired from the
•
manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power
•
down the WebDT 182 and disconnect all power sources.
Please report the problem to your device provider immediately.
•
Rear View
Front View
A
B
C
D
E
F
G
H
I
Ethernet port
USB 2.0 (2)
DVI port
DC-in
F
G
H
I
A
B
C
Audio jacks
HDMI port
RS232 COM port
C
D
USB 2.0 (2)
Power bu
tt
on
Step1:
Locate the exis
ti
ng moun
ti
ng holes
•
on the monitor.
Line the bracket holes up with the
•
holes on the back of the monitor,
as shown to the right.
Place the screws to hold the
•
moun
ti
ng bracket in place and
ti
ghten the screws (do not over-
ti
ghten).
Step2:
Remove the two M3 screws (3)
•
originally on the WebDT 180
signage appliance.
Place the WebDT 180 (2) on the
•
bracket rail with the interface
ports side facing downwards so
that the two moun
ti
ng holes on
the appliance are aligned with
the exis
ti
ng holes on the rail (see
picture).
Step3:
Apply and
ti
ghten the screws
•
into their original loca
ti
ons and
make sure that the bracket and
the WebDT 180 are properly
secured.
