background image

TROUBLESHOOTING

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

TROUBLESHOOTING STEPS

NO POWER TO KEYPADS (NO 

FUNCTIONS WORK AND NO LIGHTS 

TURN ON)

1. Verify Keypad is wired to the battery 

properly

2. Verify battery is charged

3. Replace Keypad

WRONG OUTPUT IS ACTIVATED 

WHEN BUTTON IS PRESSED

1. Improper Wiring

1. Verify Output Device is connect to 

appropriate PowerMate Output Pin

KEYPAD POWERS UP BUT NO 

FUNCTIONS WORK

1. Tripped circuit limits

2. Improper Wiring

3. Faulty Keypad

4. Faulty PowerMate

1. Check Device for Over-Current

2. Verify communication lines (TX/RX+ 

and TX/RX-) are wired to appropriate 

PowerMate Pin #’s

3. Cycle Power to the Keypad and Watch

CIRCUIT IS ALWAYS TRIPPED 

WHEN BUTTON IS PRESSED 

(INDICATOR BLINKS AND WILL 

RESET AFTER 6 SECONDS WHEN 

KEY IS PRESSED)

1. Faulty Output Device

2. Short Circuit in Wiring Harness

3. Circuit Trip limit value too low for Device

1. Verify Output Device is working 

properly

2. Check for Short Circuit in Wiring 

Harness

3. Verify Circuit Breaker value is 

sufficient for System

INDICATOR LED’S FLICKER ON AND 

OFF

1. Function has No Load

2. Stray Voltage from Harness

1. Apply Load to the Function

2. Check Shielding on Communication 

Lines

SYSTEM LOCKS UP

1. Low Battery Power

1. Cycle Power to the Keypad and 

PowerMate

2. Verify System is at Recommended 

Voltage

1. Keypad not wired/connected properly

2. Low Battery Power

3. Faulty Keypad

REVISION HISTORY

REVISION HISTORY

DATE

REVISION

COMMENTS

21/05/2018

1.0

Preliminary

24/06/2019

1.1

Draft Corrections

16/07/2019

1.2

Draft Corrections

20/05/2020

1.3

Draft Corrections

10/09/2020

1.4

Updated Installation of PM8

Page 10: DSS-PM8_SpecSheet_V.0920_A

Unit 8/27 Allgas St, Slacks Creek QLD, AUSTRALIA 4127

PO Box 1301, Slacks Creek QLD, AUSTRALIA 4127

P +61 (0)7 3290 4115      E [email protected]

S S 

Digital  witching  ystems Australia

S

S

 A 

D

Scan QR Code to see

our PowerMate Range

Scan QR Code to see

our Keypad Range

Содержание POWERMATE 8











Отзывы: