background image

 

 

 

M/S Amplifier 

Safety Precautions 

 

1.    Safety Precautions

 

 

Please do NOT connect this device to the power source, before the system is correctly wired. 

 

It is important to ensure that input voltage to the device is the same as required voltage of the device, 

otherwise the device may be damaged. 

 

There is dangerous voltage in the device, which may cause personal electric shock. Please do NOT open 

the case without permission, to avoid potential risks of electric shock. 

 

The device is not completely disconnected from power source when it is switched "OFF". For sake of 

safety, please disconnect the device from the socket if it is not in use. 

 

Please do NOT place the device where it is extremely cold or hot. 

 

Good ventilation must be provided in the working environment of the device, to avoid excessive 

10 

temperature during its operation, which may cause damages to the device. 

11 

 

Please unplug the device from power socket in raining and wet days or if the device is not in use for a 

12 

long time. 

13 

 

Please disconnect the power plug from sockets, to ensure the device has been completely disconnected 

14 

from power source, before any component is removed from or re-installed in the device or before any 

15 

electric connector of the device is disconnected or reconnected. 

16 

 

In case of any failure of the device, please do NOT open the case and repair without permission from a 

17 

professional personnel, to avoid accident or additional damages to the device. 

18 

 

Please do NOT place any corrosive chemicals near or on the device. 

19 

 

20 

2

Matters needing attention 

21 

 

Our company provides a three-year free warranty service (including free replacement parts) over quality 

22 

issues  as  from  the  date  of  purchase,  provided  that  the  device  is  installed  and  used  in  accordance  with 

23 

requirements specified in the User Manual. 

24 

 

For  warranty,  the  user  must  show  the  Warranty  Card  and  the  receipt  kept  by  the  user  and  purchase 

25 

invoice of the device as supporting documents. 

26 

 

The following conditions are beyond the scope of warranty: 

27 

1

Product damage due to improper installation, use or handling; 

28 

2

Product  damage  due  to  abnormal  conditions  (such  as  excessive  power  source  voltage  or  ambient 

29 

humidity); 

30 

3

Product damage due to acts of God; 

31 

4

Product SN is changed, altered or removed; 

32 

5

Product has been repaired or modified by any person without duly authorization from our company;   

33 

 

Please keep the User Manual and Warranty Card in good custody. 

34 

 

For issues and precautions not mentioned in this User Manual, if required, please contact the distributor 

35 

or visit our website at 

http://www.dsppatech.com

. 

36 

 

In case of any failure in the warranty period, please contact service personnel (or distributor) of our 

37 

company for service. The company shall not be made liable for damages due to unauthorized 

38 

dis-assembly or maintenance or service by unauthorized personnel. 

39 

 

40 

 

41 

 

42 

43 

Содержание DA8250
















Отзывы: