background image

A

NTI

-M

ODE

 8033C

INEMA

Recycling information

The product you have purchased is marked according to the 

Waste 

Electrical and Electronic Equipment Directive

 (WEEE Directive). 

There are take-back systems in place that help to preserve nature 
and natural resources when products are disposed of appropriately. 

If you need to dispose of this product, use the take-back system 
that has dedicated collection facilities for electronic equipment. Do 

not put the product into household waste disposal! 

Also, the product has been manufactured using parts and processes that follow the directive 
of the Restriction of the use of certain Hazardous Substances in Electrical and Electronic 

Equipment (RoHS).

Intended Use

The Anti-Mode 8033s have been designed for normal indoor use and be connected to other 
equipment with cables not exceeding 3m (10 feet) in length. If you use cables of extended 

length, check that their quality is sufficient and observe electrostatic discharge precautions 
when   connecting   or   disconnecting   them.   Use   of   the   device   outdoors,   in  humid   or   other 

extreme   environments,   may   cause   reduced   performance   or   risks   to   the   user   of   the 
equipment.

Rev. 1.9

2012-03-20

Page 2 (12)

Содержание Anti-Mode 8033Cinema













Отзывы: