Document:
RE-BCC8HD 1A5
Document:
RE-BCC8HD 1A5
Document:
RE-BCC8HD 1A5
Page:
3
Page:
3
OWNER'S MANUAL
RE-BCC8HD camera license plate
DSE srl - Digital Surveillance Equipment - WWW.DSE.EU
28
ON
ON OFF
OR NOT
29
OFF
OFF
ON ON ON
30
ON
OFF
ON ON ON
31
OFF
ON ON ON ON
32
ON
ON ON ON ON
The settings
of
the camera factory
there
RS485 communication are: PELCO
PROTOCOL D SPEED '2400 bps ADDRESS: 1
Through the RS485 port is
send commands to
recalling camera presets the following system:
CALL 200
- With this command gives you access to the remote modification of the IR
CALL 200
- With this command gives you access to the remote modification of the IR
LED brightness. When you enter the preset 200 act on the joystick by moving it up and down to
change the power of the LEDs. Check the result on the monitor.
CALL + PRESET 201
- ends the adjustment With this command
CALL + PRESET 201
- ends the adjustment With this command
brightness of the LEDs and confirms
the setting.
CALL 101
- Changes the video output in CVBS, namely standard analog, for coupling
CALL 101
- Changes the video output in CVBS, namely standard analog, for coupling
with analog DVR that do not support the AHD The technology requires the switching time of 5
seconds. Close the OSD menu of the camera before performing the switching.
CALL + PRESET 102
- Switch the video output AHD 720P (requires DVR technology that support
CALL + PRESET 102
- Switch the video output AHD 720P (requires DVR technology that support
AHD)
CALL 95
- Opens the OSD menu of the camera which is described below. Inside one
CALL 95
- Opens the OSD menu of the camera which is described below. Inside one
moves with the navigation arrows (or joystick) and confirming with the IRIS
OSD MENU - SPEED 'THE SHUTTER
The camera has an on-screen menu that is called up Preset 95 as seen above.
In regular operating conditions it is not necessary to intervene in this menu, so it's highly
advisable not to do so to avoid inadvertently change the factory settings.
E 'can, however, take action on the default options to optimize according to the application real
vision. In acting in the OSD is important to remember that some adjustments
they are essential
for
the
good
operation of reading license plates and must not be changed randomly.
Below we listed the necessary adjustments.
LENS
This parameter must be maintained to MANUAL as the lens used is a manual varifocal.
EXPOSURE / SHUTTER
Click EXPOSURE SHUTTER and then to open this section of the menu
The factory setting of this parameter and 1/400 and it is possible to keep it unchanged until the
speed of the means less than about 120 Km / h.
If the means traveling at a higher speed is good to increase this value to 1/1000, 1/2000 and
beyond. More it provides for the high speed of the medium to resume more it will take a short
amount of electronic shutter time. Note, however, most will shorten the time to shutter the more
you reduce the overall brightness of the video. It usually takes no more than 1/2000 sec. If the
means passing through lenses, as in rest areas, you can reduce the shutter at 1/200 and less
and this
will increase
there
brightness
picture
allowing you to see the details of the medium. The maximum speed of the means to take can
not exceed 180 km / h.
Be careful not to set this parameter to AUTO. The automatic shutter provides an excellent
overall image but does not allow the license plate.
EXPOSURE / AGC
This setting is located in the section EXPOSURE already seen above, immediately below the
shutter adjustment. The AGC is designed to increase the overall brightness of the night
especially when it reaches values greater than 5, however, it introduces an inevitable video
noise. If this is not acceptable, desirable that, AGC values lower around 3/4.
DAY & NIGHT
This parameter should strictly be left on EXT to allow a proper ignition control of the IR.
BACKLIGHT
Recommended OFF
The other OSD parameters are irrelevant in ANPR function.
PROBLEMS AND SOLUTIONS
Image B / W day
- lit illuminators, adjust IR activation threshold. If the image is B / N IR off the
Image B / W day
- lit illuminators, adjust IR activation threshold. If the image is B / N IR off the
IR filter is in the wrong position due to mechanical shock, deenergize and restore control
camera, then secure it more solidly.
IR LED does not light up at night
- Adjust the ignition threshold. Verify that there is a source of
IR LED does not light up at night
- Adjust the ignition threshold. Verify that there is a source of
light that illuminates the sensor on the rear of the camera.
Glare on the plate
- Avoid directly oriented towards the camera lights (min 30 °).
Glare on the plate
- Avoid directly oriented towards the camera lights (min 30 °).
The plate is moved
- Check goal setting. Reduce the shutter speed to 1/1000 or 1/1500
The plate is moved
- Check goal setting. Reduce the shutter speed to 1/1000 or 1/1500
Targa too bright or dark at night
- Adjust the power of the LEDs according to the shooting
Targa too bright or dark at night
- Adjust the power of the LEDs according to the shooting
distance
The power of LEDs varies after a reset
- Confirm the IR power setting by moving down the
The power of LEDs varies after a reset
- Confirm the IR power setting by moving down the
mini joystick
