7
DIAGRAM 2-2
Hook-up for PC4010/4020 v3.0 Panels
CAUTION
: Due to the sensitivity of the RF circuitry, avoid any contact with the coils
and potentiometers on the LINKS2450 circuit board.
*If power supply supervision is required for the LINKS2450 VTX terminals, use the
PC4204. If no supervision is needed, you can use the PS1520 or the control panel
Bell+/Aux- terminals .
NOTE
: Programming section [01], option 2 must be ON for LINKS2450 to work with
these panels.
10
Program the LINKS2450 Toggle Options on the Panel
At a PC4010 or PC4020 system keypad, enter reference # [000405] and [*], or scroll
to the “LINKS2XXX” programming section. (See the “How to Program” section in your
PC4010/4020
Installation Manual for more information.) Use the arrow keys (< >) to
scroll to each of the following toggle options. Press [*] to toggle the option ON or OFF.
Record your programming choices in the worksheets at the end of this manual.
LINKS2XXX
Yes
When enabled the PC4010 or PC4020 will send the events
that are programmed to the LINKS2450. The PC4010/
4020 will only send the events that have reporting codes
programmed and dialer directions enabled for them.
No
The PC4020 will not send events to the LINKS2450.
Default condition is No.
NOTE
: The Communications Toggle option “Comms Enabled” must also be set to
Yes for the PC4010/4020 to be able to send events to the LINKS2XXX.
To disable the PC4010/4020 telephone communications, but still allow the PC4010/
4020 to communicate events through the LINKS2XXX, set “Comms Enabled” to
Yes, and the Dialer Directions to No for all 3 telephone numbers. Leaving all 3
telephone numbers unprogrammed will also disable telephone communications.
See the “Communications Programming” section in your PC4010/4020
Installation
Manual for more information.
Alarm/Restore
Yes
Alarm and Restoral reporting codes are sent to the central
station by the LINKS2450.
No
Alarm and Restoral reporting codes are not sent to the
LINKS2450.
Default: No (Yes on PC4010CF/4020CF panels)
Open/Close
Yes
Opening and Closing reporting codes are sent to the
central station by the LINKS2450.
No
Opening and Closing reporting codes are not sent to the
LINKS2450
Default: No (Yes on PC4010CF/4020CF panels)
All others
Yes
All other reporting codes are sent to the central station by
the LINKS2450.
No
All other reporting codes are not sent to the LINKS2450
Default: No (Yes on PC4010CF/4020CF panels)
To exit the LINKS2XXX programming section, press [#].
Program Panel Supervision for the LINKS2450
Panel supervision of the LINKS2450 is recommended when connected to PC4010/
4020 panels. To have the panel supervise the LINKS2450, make sure the zone that
the LINKS2450 is connected to on the panel is programmed for LINKS Supervisory
(zone type [28]). When the zone is programmed this way, if the YEL terminal is not
grounded (e.g. the wire is cut), the panel will generate a zone trouble and a LINKS
trouble and will send the reporting code for the zone.
See your PC4010/4020
Installation Manual for information on zone programming.
7
DIAGRAM 2-2
Hook-up for PC4010/4020 v3.0 Panels
CAUTION
: Due to the sensitivity of the RF circuitry, avoid any contact with the coils
and potentiometers on the LINKS2450 circuit board.
*If power supply supervision is required for the LINKS2450 VTX terminals, use the
PC4204. If no supervision is needed, you can use the PS1520 or the control panel
Bell+/Aux- terminals .
NOTE
: Programming section [01], option 2 must be ON for LINKS2450 to work with
these panels.
10
Program the LINKS2450 Toggle Options on the Panel
At a PC4010 or PC4020 system keypad, enter reference # [000405] and [*], or scroll
to the “LINKS2XXX” programming section. (See the “How to Program” section in your
PC4010/4020
Installation Manual for more information.) Use the arrow keys (< >) to
scroll to each of the following toggle options. Press [*] to toggle the option ON or OFF.
Record your programming choices in the worksheets at the end of this manual.
LINKS2XXX
Yes
When enabled the PC4010 or PC4020 will send the events
that are programmed to the LINKS2450. The PC4010/
4020 will only send the events that have reporting codes
programmed and dialer directions enabled for them.
No
The PC4020 will not send events to the LINKS2450.
Default condition is No.
NOTE
: The Communications Toggle option “Comms Enabled” must also be set to
Yes for the PC4010/4020 to be able to send events to the LINKS2XXX.
To disable the PC4010/4020 telephone communications, but still allow the PC4010/
4020 to communicate events through the LINKS2XXX, set “Comms Enabled” to
Yes, and the Dialer Directions to No for all 3 telephone numbers. Leaving all 3
telephone numbers unprogrammed will also disable telephone communications.
See the “Communications Programming” section in your PC4010/4020
Installation
Manual for more information.
Alarm/Restore
Yes
Alarm and Restoral reporting codes are sent to the central
station by the LINKS2450.
No
Alarm and Restoral reporting codes are not sent to the
LINKS2450.
Default: No (Yes on PC4010CF/4020CF panels)
Open/Close
Yes
Opening and Closing reporting codes are sent to the
central station by the LINKS2450.
No
Opening and Closing reporting codes are not sent to the
LINKS2450
Default: No (Yes on PC4010CF/4020CF panels)
All others
Yes
All other reporting codes are sent to the central station by
the LINKS2450.
No
All other reporting codes are not sent to the LINKS2450
Default: No (Yes on PC4010CF/4020CF panels)
To exit the LINKS2XXX programming section, press [#].
Program Panel Supervision for the LINKS2450
Panel supervision of the LINKS2450 is recommended when connected to PC4010/
4020 panels. To have the panel supervise the LINKS2450, make sure the zone that
the LINKS2450 is connected to on the panel is programmed for LINKS Supervisory
(zone type [28]). When the zone is programmed this way, if the YEL terminal is not
grounded (e.g. the wire is cut), the panel will generate a zone trouble and a LINKS
trouble and will send the reporting code for the zone.
See your PC4010/4020
Installation Manual for information on zone programming.