manualshive.com logo in svg

Drylam DRYLAM SL, Инструкция по эксплуатации

Поделиться
Скачать
Drylam DRYLAM SL Скачать руководство пользователя страница 8

5

I. Unpacking

Remove the laminator from its box by grasping the housings and pulling up. Do not use rollers or shafts 
as handles - this could cause damage. Choose a location for the laminator that is clean, well-lit and draft 
free. Make sure it is not in the path of any fans, room air conditioners, or positioned too close to the wall. 
The laminator comes to you ready to load the  film onto the supply mandrels, thread the  film through the 
machine, and install the feedtable.  

II. Information About Laminating Film

Laminating  film is made up of two layers: a glossy layer which gives the lamination its strength, clarity and 
rigidity, and a dull or matte side which is heat activated and serves as the “glue” to bond the  film to the 
product being laminated. Once heated, small amounts of the “glue” side can stick to the heat shoes and 
rollers and must be periodically cleaned from the laminator.

Laminating  film is available in a variety of different lengths, and thicknesses. The SL27 Laminator 
is designed to use 1.5 mil (#150), and 3 mil (#300),  film thicknesses.                               

III. Operating

A. Control Panel
The control panel is located on the left side of the laminator.  This panel is used to control the various 
machine functions listed below.

Heat  (A,M,N)
The temperature can be turned either “on” or “off” using the the heat switch (A) which is located on the 
control panel. The heat can be controlled manually using the heat control knob (N) located on the left 
housing (E). A thermostat (M) is also located on the left housing (E) and provides the current temperature  
of the laminator.  Note: depending on room conditions and desired set point, it will take between 20 and 
30 minutes for the laminator to heat up to desired temperature.

Motor  (B)
To stop the motor, press the “Stop/Reverse” switch in the “Stop” (nuetral) position. To start the motor, 
press the “Stop/Reverse” switch in the “Fwd” location. To reverse the motor, press the “Stop/Reverse” 
switch in the “Rev” location. The motor will remain in reverse as long as the button is depressed. 

Additional Features
Keyswitch
The keyswitch (located just below the control panel) locks out the motor, allowing the machine to remain 
heated; yet, preventing unauthorized usage when in the locked position.

Содержание DRYLAM SL



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды