manualshive.com logo in svg

Drolet Eldorado DB02610, Инструкция по установке и эксплуатации, Страница: 24 / 51

Поделиться
Скачать
Drolet Eldorado DB02610 Скачать руководство пользователя страница 24

Eldorado Installation and Operation Manual 

 

 

24 

5.1.3  Replacing the Door Gasket 
It  is  important  to  maintain  the  gasket  in  good  condition.  After  a  year  or  more  of  use,  the 
door gasket will compress and become hard, which may allow air to leak past it. You can 
test the condition of the door gasket by closing and latching the door on a strip of paper. 
Test  all  around  the  door.  If  the  paper  slips  out  easily  anywhere,  it  is  time  to  replace  the 
gasket.  

Use the correct replacement gasket that you can purchase from your retailer. The diameter 
and density of the gasket is important to getting a good seal. 

Place  the  door  face-down  on  something  soft  like  a  cushion  of  rags  or  piece  of  carpet. 
Remove the old gasket from the door by pulling and prying it out with an old screw driver. 
Then use the screwdriver to scrape the old gasket adhesive from the door. Now run a 1/4” 
(6  mm)  bead  of  high  temperature  silicone  in  the  door  gasket  groove.  Starting  from  the 
middle  of  the  hinge  side,  press  the  gasket  into  the  groove.  Do  not  stretch  the  gasket  as 
you place it. Leave the gasket about 1/2” long when you cut it and press the end into the 
groove. Tuck any loose fibres under the gasket and into the silicone. Close the door and 
do not use the stove for 24 hours. 

5.1.4  Replacing the Glass Gasket and/or the Glass 

It is a good idea to replace the glass gasket when the door gasket is replaced. The gasket 
is  flat,  adhesive-backed,  woven  fibreglass.  Remove  the  glass  retaining  screws  (A)  and 
both metal frames (B) that holds the glass (C) to the door frame (D). Lift out the glass (C) 
and pull off the old gasket. This is a good time to clean the glass thoroughly. 

 

 

The  gasket  must  be  centred  on  the  edge  of  the  glass.  To  do  this  easily,  peel  back  a 
section  of  the  paper  covering  the  adhesive  and  place  the  gasket  on  a  table  with  the 
adhesive  side  up.  Stick  the  end  of  the  gasket  to  the  middle  of  one  edge,  then  press  the 
edge  of  the  glass  down  onto  the  gasket,  taking  care  that  it  is  perfectly  centred  on  the 
gasket. Peel off more of the backing and rotate the glass and press the next section onto 
the gasket. Do not stretch the gasket as you place it. Continue until you get to the start and 
trim the gasket to length. Now pinch the gasket to the glass in a U shape, all around the 
glass.  Reinstall  the  glass,  being  careful  to  centre  the  glass  carefully  in  the  door.  Do  not 
over-tighten  the  screws.  Note  that the  two  main  causes of broken door  glass are  uneven 
placement in the door and over-tightening of retaining screws. 

Содержание Eldorado DB02610




















































Отзывы:

Нет отзывов