DriSteem GTS LX Series Скачать руководство пользователя страница 51

Страница: 51 / 88

GTS HUMIDIFIER LX SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

General venting (continued)

INSTALLATION

Table 49-1:
Equivalent vent lengths

Description

2" - 3" diameter

4" diameter

6" diameter

feet

meter

feet

meter

feet

meter

Long radius 90° elbow

0.9

1.2

1.8

Medium radius 90° elbow

1.5

2.0

3.0

Mitered 90° elbow

2.4

3.3

4.9

Long radius 45° elbow

1.5

0.5

0.6

0.9

Medium radius 45° elbow

2.5

0.8

1.0

1.5

Mitered 45° elbow

1.2

1.6

2.4

Concentric vent termination

1.5

2.0

Tee

4.9

6.5

9.8

3" to 2" (80 to 60 mm) step down adapter

1.5

2.0

3.0

FIGURE 49-1: VENT ELBOWS AND TEES

long

mitered

medium

concentric

Note: A maximum of eight elbows, including terminations, are allowed.

humidifier must be within the ranges shown in Table

49-2 from full output to minimum output.

• Do not common vent products of combustion the LX

series GTS humidifier with another LX series or any

other appliance.

• Flue gas outlet and combustion air inlet adapters

accept PVC, CPVC, Polypropylene and stainless steel

piping.

• Flue vent adapters, if used, must be installed vertically

at the point of connection to the GTS humidifier LX

series.

• Ensure that distances from vent terminal to adjacent

public walkways, buildings, and openable windows

and building openings are consistent with National

Fuel Gas Code, ANSI Z223.1, CAN/CGA B149

Installation Codes, National Gas Safety Code

(Installation & Use) Regulations (latest revision), or

governing codes.

• In areas accessible to the public, vent terminal must be

at least 7' (2.1 m) above ground level to prevent burns

from hot terminal surface.

• The vent terminal and air intake locations must be at

sufficient height above ground level to prevent blocking

by expected snowfall.

• Building materials must be protected from degradation

by flue gases.

• Maintain minimum horizontal clearance of 4' (1.22 m)

from electric meters, gas meters, regulators, and relief

equipment.

Table 49-2:

Venting pressure

Description

Minimum

Maximum

Flue gas outlet pressure

-0.05" WC

(+12 Pa)

+0.45" WC

(+112 Pa)

Combustion air inlet pressure

-0.45" WC

(-112 Pa)

+0.05" WC

(+12 Pa)

Содержание GTS LX Series

























































































Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды

DriSteem GTS LX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды