Drill Master DRILL MASTER 96526 Скачать руководство пользователя страница 14

Страница: 14 / 18

Page 14

SKU 96526

For technical questions, please call 1-800-444-3353.

The Drill/Driver has a variable speed for drilling. To vary the speed of the drilling

action, vary the pressure on the Power Switch (10).
Drill only as deep as is necessary. Do not drill deeper than necessary into walls

or other areas where you cannot identify any possible hazards behind the drilling

surface.
To reduce jamming as the drill bit breaks through the workpiece, decrease the

drilling pressure when the point of the drill bit breaks through the surface of the

workpiece.
When you have drilled the hole, remove the drill bit from the hole while the Drill/

Driver is still rotating. This prevents the drill bit from getting caught in the hole

and causing damage.
Release the Power Switch (10) to stop the Drill/Driver.

InSpECtIOn, MAIntEnAnCE, AnD CLEAnIng

Risk of serious personal injury from accidental starting

or electric shock. turn the power Switch of the tool to its

“OFF” position and unplug the tool from its electrical outlet

before performing any inspection, maintenance, or cleaning

procedures.
Damaged equipment can fail, causing serious personal

injury. Do not use damaged equipment. If abnormal noise or

vibration occurs, have the problem corrected before further

use.

CAutIOn!

Always disconnect the Battery (29) from the tool before performing

and inspection, maintenance, or cleaning.

Before each use,

examine the general condition of the Drill/Driver. Check for

loose screws, misalignment or binding of moving parts, broken parts, damaged

electrical wiring, and any other condition that may affect its safe operation. Run

the Drill/Driver for about ten seconds to ensure all moving parts are running

smoothly and there are no loose parts, rattles, or sparking that would indicate

defects. if a problem occurs, turn off the Drill/Driver immediately and have the

problem corrected before further use.

Do not use a damaged tool.

the Drill/Driver is equipped with a 24V nickel-Cadmium Battery (type:

1300 mAh ni-Cd Rechargeable).

With proper care, the Battery (29) can be

recharged many, many times. Follow the Steps below to ensure proper Battery

care:

Always switch to a fresh Battery when tool performance begins to diminish.

Severe heat is most destructive to a Battery. The more heat generated, the

10.

11.

12.

13.

14.

•

WARnIng

Содержание DRILL MASTER 96526



















Результаты поиска

Содержание DRILL MASTER 96526

Отзывы:

Похожие инструкции для DRILL MASTER 96526

Бренды по названию

Популярные бренды

Drill Master DRILL MASTER 96526, Руководство по установке и эксплуатации

Результаты поиска

Содержание DRILL MASTER 96526

Отзывы:

Похожие инструкции для DRILL MASTER 96526

Бренды по названию

Популярные бренды