background image

The original ROOTS blower still leads the way

.

DVJ WHISPAIR

 

Dry Exhauster

Installation, Operation & Maintenance

Contents

Information Summary ...........................................................1
Warranty and Limitation of Liability ........................................2 
Operating Characteristics .....................................................3
Operating Limitations ............................................................4
Installation ...................................................................... 5-10

Lubrication ................................................................... 10-11
Operation ..................................................................... 12-13
Troubleshooting ..................................................................14 
Maintenance/Replacements ......................................... 16-22
Sectional Drawings ....................................................... 23-26

o

  Check shipment for damage. If found, file claim with 

carrier and notify nearest Sales Office. See List on last 
page.

o

  Unpack shipment carefully and check contents against 

packing List. Notify Sales Office if a shortage appears.

o

  Store in a clean, dry location until ready for installation. 

Lift by methods discussed under installation to avoid 
straining or distorting the equipment. Keep covers on 
all openings. Protect against weather and corrosion if 
outdoor storage is necessary.

o

  Read LIMITATIONS and INSTALLATION sections in this 

manual and complete the installation.

o

  Provide for adequate safeguards against accidents to 

persons working on or near the equipment during both 
installation and operation. SEE SAFETY PRECAUTIONS.

o

  Install all equipment correctly. Foundation design must be 

adequate and piping carefully done. Use recommended 
accessories for operating protection.

o

  Make sure both driving and driven equipment is correctly 

lubricated before start-up. See LUBRICATION.

o

  Read starting checkpoints under OPERATION. Run 

equipment briefly to check for installation errors and make 
corrections. Follow with a trial run under normal operating 
conditions.

o

  In event of trouble during installation or operation, do 

not attempt repairs of Roots furnished equipment. Notify 
nearest Sales Office giving all nameplate information plus 
an outline of operating conditions and a description of the 
trouble.

o

  Unauthorized attempts at equipment repair may void 

Manufacturer’s warranty. Units out of warranty may be 
repaired or adjusted by the owner. It is recommended 
that such work be limited to the operations described 
this manual, using Factory Parts. Good inspection and 
maintenance practices should reduce the need for 
repairs.

Do These Things To Get The Most From Your ROOTS

 Blower

ILRB-3006 0810

Содержание Roots DVJ WHISPAIR


























Отзывы: