7
GENERAL SAFETY INSTRUCTIONS
!
WARNING
READ ALL INSTRUCTIONS.
Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
The term “power tool” in all of the warnings listed below refers to
your cordless power tool.
SAVE THESE INSTRUCTIONS
1. WORK AREA
a. Keep work area clean and well lit.
Cluttered and dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres, such as
in the presence of fl ammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power
tool.
Distractions can cause you to lose control.
2. ELECTRICAL SAFETY
a. Charger plug must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such
as pipes, radiators, ranges and refrigerators.
There is an
increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet conditions.
Water
entering a power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the charger. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or
entangled cords increase the risk of electric shock.
e. When using a charger outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f. Do not use the charger when the cord or plug are damaged;
the cord or plug should be replaced immediately at a
certifi ed Dremel Service Centre.
3. PERSONAL SAFETY
a. Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b.
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Avoid accidental starting.
Carrying power tools with your
finger on the switch invites accidents.
d. Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e. Do not overreach.
Keep proper footing and balance at all
times. This enables better control of the power tool in
unexpected situations.
f.
Dress
properly.
Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used.
Use of these devices can reduce dust related
hazards.
4. POWER TOOL USE AND CARE
a. Do not force the power tool. Use the correct power tool for
your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on
and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c. Turn the power tool off before making any adjustments,
changing accessories, or storing.
Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tools operation. If damaged, have the
power tool repaired before use.
Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work to be
performed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. BATTERY USE AND CARE
a. Recharge only with the charger specifi ed by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fi re when used with
another battery pack.
b. Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, fl ush with
water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6. SERVICE
a. Have your power tool serviced by a qualifi ed repair person
using only identical replacement parts.
This will ensure that
the safety of the power tool is maintained.
GB
GB
2610398733-CN-Stylus-0805.indb 7
2610398733-CN-Stylus-0805.indb 7
27-5-2008 12:12:14
27-5-2008 12:12:14
Содержание Stylus Lithium-Ion
Страница 77: ...2610398733 CN Stylus 0805 indb 77 2610398733 CN Stylus 0805 indb 77 27 5 2008 12 15 41 27 5 2008 12 15 41 ...
Страница 78: ...2610398733 CN Stylus 0805 indb 78 2610398733 CN Stylus 0805 indb 78 27 5 2008 12 15 47 27 5 2008 12 15 47 ...
Страница 79: ...2610398733 CN Stylus 0805 indb 79 2610398733 CN Stylus 0805 indb 79 27 5 2008 12 15 47 27 5 2008 12 15 47 ...
