Dremel SM20 Скачать руководство пользователя

Страница: 4 / 60

-4-

Wear  personal  protective  equipment.
Depending  on  application,  use  face  shield,
safety  goggles  or  safety  glasses.  As
appropriate,  wear  dust  mask,  hearing
protectors,  gloves  and  workshop  apron
capable  of  stopping  small  abrasive  or
workpiece  fragments.  The  eye  protection
must  be  capable  of  stopping  flying  debris
generated  by  various  operations.

The dust

mask or respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.

Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.

Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.

Hold  power  tool  by  insulated  gripping
surfaces  only,  when  performing  an
operation where the cutting accessory may
contact  hidden  wiring  or  its  own  cord.

Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live” and shock the operator.

Position the cord clear of the spinning
accessory.

If you lose control, the cord may be

cut or snagged and your hand or arm may be
pulled into the spinning accessory.

Never lay the power tool down until the
accessory has come to a complete stop.

The spinning accessory may grab the surface
and pull the power tool out of your control.

Do not run the power tool while carrying it
at your side.

Accidental contact with the

spinning accessory could snag your clothing,
pulling the accessory into your body.

Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the
housing and excessive accumulation of
powdered metal may cause electrical hazards.

Do not operate the power tool near
flammable materials.

Sparks could ignite

these materials.

Do not use accessories that require liquid
coolants.

Using water or other liquid coolants

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging

causes  rapid  stalling  of  the  rotating  accessory
which  in  turn  causes  the  uncontrolled  power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.

For  example,  if  an  abrasive  wheel  is  snagged
or  pinched  by  the  workpiece,  the  edge  of  the
wheel  that  is  entering  into  the  pinch  point  can
dig into the surface of the material causing the
wheel  to  climb  out  or  kickout.  The  wheel  may
either  jump  toward  or  away  from  the  operator,
depending  on  direction  of  the  wheel’s
movement  at  the  point  of  pinching.  Abrasive
wheels may also break under these conditions.

Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below.

Maintain  a  firm  grip  on  the  power  tool  and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle,  if  provided,  for  maximum  control
over  kickback  or  torque  reaction  during
start-up.

The operator can control torque

reactions or kickback forces, if proper
precautions are taken.

Never place your hand near the rotating
accessory.

Accessory may kickback over your

hand.

Do not position your body in the area where
power tool will move if kickback occurs.

Kickback will propel the tool in direction
opposite to the wheel’s movement at the point
of snagging.

Use  special  care  when  working  corners,
sharp  edges  etc.  Avoid  bouncing  and
snagging  the  accessory.

Corners, sharp

edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.

Do not attach a saw chain woodcarving
blade or toothed saw blade.

Such blades