background image

9

DRAWMER

 1973 O

PERATOR’S 

M

ANUAL

QUICK SETUP PROCEDURE

Please note that the following procedure is only a guide. All audio is different, requiring numerous settings, however,
this should give a good staring point:

1) Set the compressor settings to be the same on all bands - 

Threshold

 fully counter-clockwise, 

Gain

 at 0dB,

the

 Attack 

in a mid position (2 or 3) and 

Release

 set to F(ast). The overall 

Gain

 control should be set to 0dB,

and the 

Mix

 at 0 (Wet).

2) Turn on the 

Bypass

 switch (bottom right) so that the input signal is heard without compression and adjust the

incoming signal until the 

VU meters

 rear 0dB. Set the 

Bypass

 switch back to Normal.

3) With the 

Low X-Over Frequency

 set fully counter-clockwise, and the 

High X-Over Frequency

 set fully  clockwise,

listen to the audio and bring in the two knobs to the positions that you think the cross-over points should be set
- generally to separate the main bass and treble sounds from the mid-range. Using a combination of 

Mute

 and

Bypass

 switches for the various bands allows the operator to monitor only the frequencies that are required and so

tune the low, mid and high frequencies.

4) Keeping an eye on the 

Gain Reduction Meters

 alter the 

Threshold 

level control for each band until the desired

compression level is achieved - a G.R. level up to -10dB is acceptable.

5) Adjust the 

Gain 

control of each band until 0dB is reached on the 

Output VU meter

. To see only the band that

is being adjusted on the VU meter 

Mute

 the other two bands.

6) Set the 

Attack

 and 

Release 

settings of each band to suit the audio being compressed.

7) The 

Threshold

 and 

Gain 

of each band can be modified to achieve the desired compression, levels and tonal

balance to the overall signal.

8) At this point the 

Bypass 

switch can be toggled to listen to the affect that the 1973 is having on the audio.

Adjust to suit.

9) Once each band is setup correctly modify the overall 

Output Gain

 and 

Mix

 until the VU meters read 0dB

(more if in +10dB VU mode) and the desired amount of compression is heard.

Below is an example setup that could be used for a General Pop Mix, though, of course, as all music is diverse and
varied, will not be ideal elsewhere.

Содержание 1973













Отзывы: