Draper Nocturne+ E Скачать руководство пользователя страница 3

Section 2 -

 Mounting Case with Brackets - Wall Installation

Section 3 -

 Mounting Case Directly to Ceiling or Wall

1. 

Attach Mounting Brackets to Case as a spacer between Case and wall.

Please Note:

 Leave a 1¾" 

(44mm)

 gap between Endcap and Mounting Bracket 

(Fig. 4)

, and tighten set screws.

2. 

Remove roller assembly.

A. 

Remove screws from bottom of Case, remove Cover and set aside 

(Fig. 5)

.

B. 

Remove Quick Release Pin from Idler End of Roller Assembly.

C. 

Remove Roller Assembly, Idler End first, and set aside.

3. 

Mount to Ceiling / Wall.

A. 

Using mounting holes in endcaps as a guide 

(Fig. 6)

, drill pilot holes on 

both ends of Case.

B. 

Attach to mounting surface using appropriate fasteners.

Please Note:

 Installer is responsible for selecting mounting hardware 

appropriate for site conditions. 

4. 

Once Case is secured to mounting surface, re-install Roller Assembly,  
Quick Release Pin and Cover.

5. 

Proceed to Section 4  

(Installing Cable Guides)

.

Section 2.1 - Attaching Mounting Brackets

1. 

Attach mounting brackets to wall using #10 flat head screws installed flush with bracket.  
Be sure to use AT LEAST 2 of top mounting holes 

(Fig. 2)

.

Section 2.2 - Attaching Case to Mounting Brackets

1. 

Attach Case to brackets and tighten Set Screws 

(Fig. 3)

.

2. 

Proceed to Section 4 

(Installing Cable Guides)

.

Figure 2

Figure 3

Figure 4

Figure 5

Tighten 
set screws.

1

2

3

Leave a 1

"

(44mm)

 gap.

Attach 
mounting bracket 
as spacer and 
tighten set screws.

Remove

cover.

Remove quick 

release pin.

Remove roller 

assembly.

A

B

C

Remove screws from 

bottom of case.

WALL

MOUNT HOLES

 

CEILING

MOUNT HOLES

 

WALL

MOUNT HOLES

 

CEILING

MOUNT HOLES

 

Figure 6

page 3 of 12

N E

Содержание Nocturne+ E













Отзывы: