Motorized Roller/Fabric Installation
The bottom access panel m
u
st be remo
v
ed fi rst. The Access/M
u
ltiView has
two roller/fabric assemblies. The one eq
u
ipped with a complete projection
screen fabric is installed fi rst, higher in the brackets, and connects to the
left-hand j
u
nction box. The second roller has black masking strips at the sides
and no fabric in the middle: it installs lower in the brackets and connects to the
right-hand j
u
nction box.
The motor end mo
u
nting brackets ha
v
e steel mo
u
nting rings with prongs that
engage with motor head.
To engage the motor end bracket fl ange abo
v
e the two channels in the top of
the screen ho
u
sing, rotate the bracket approximately 45° co
u
nterclockwise
to allow the top s
u
rface of the motor bracket to rest fl at against the top inside
of the ho
u
sing. Rotating the bracket clockwise
u
ntil it is engaged with the
channels, slide it along the length of the ho
u
sing toward the electrical j
u
nction
box at left end of case.
Engage the idler end bracket (rectang
u
lar mo
u
nting pad) in the same manner
as the motor end bracket and slide it toward the opposite end of the screen
ho
u
sing. Do not tighten the set screws on this bracket
u
ntil the roller/fabric
assembly is installed.
Locate the
v
iewing s
u
rface roller/fabric assembly and remo
v
e the retaining
clip and fl at steel washer from the idler end pin.
Raise the
v
iewing s
u
rface roller/fabric assembly
u
p into the screen ho
u
sing
and engage the head of the motor completely into the motor mo
u
nting
bracket. The steel clip on the motor mo
u
nting ring m
u
st snap into the
groo
v
e on the motor. Once this is done the clip m
u
st be man
u
ally p
u
lled down
away from the mo
u
nting ring to disengage motor. Make s
u
re the limit switch
adj
u
stment knobs are
v
isible from bottom of ho
u
sing. (This will req
u
ire two
people to perform safely.)
While s
u
pporting the idler end of the roller, slide the idler end mo
u
nting
bracket toward the roller. Insert the roller pin into the nylon b
u
shing on the
idler end mo
u
nting bracket.
The roller idler pin needs to go thro
u
gh the idler bracket far eno
u
gh to allow
the steel washer and retaining clip to be reinstalled on the pin. Fail
u
re to
replace the washer and retaining clip as shown co
u
ld res
u
lt in the separation
of the roller from the brackets.
The fabric/roller assembly and brackets will need to be mo
v
ed left or right
u
ntil centered in case. Tighten two set screws on each roller mo
u
nting bracket
u
sing
1
/
8
" hex key.
Locate the masking roller assembly and remo
v
e the retaining clip from motor
st
u
d and remo
v
e retaining clip and washer from idler pin.
Raise masking roller
u
p into screen ho
u
sing making s
u
re motor is on the
right (as
v
iewed by a
u
dience). Engage the motor st
u
d inside sq
u
are b
u
shing.
Engage the idler pin all the way thro
u
gh the ro
u
nd b
u
shing on left roller
Access MultiView Installation/Operating Instructions
page 2 of 4
Motorized Roller/Fabric Removal
Re
v
erse the instr
u
ctions abo
v
e
u
nder “Motorized Roller/Fabric Installation”
for remo
v
al of the
u
nit.
Operation
When screen and masking are fi rst operated,
be cautious!
Cycle
u
nit down
and
u
p se
v
eral times to confi rm satisfactory operation. Factory adj
u
sted limit
switches sho
u
ld a
u
tomatically stop screen or masking when f
u
lly down or
f
u
lly
u
p. Separate controls operate screen and masking motors,
u
nless the
Access/M
u
ltiView Control is
u
sed.
110-120v SINGLE STATION CONTROL (2 standard)—
3-position UP-OFF-
DOWN switches permit operation to be stopped at any point.
110-120v MULTIPLE STATION CONTRO
L—Switches are similar in appear-
ance to 110-120
v
Single Station Control. Screen or masking stops when
switch is released and may be restarted in either direction.
ACCESS/MULTIVIEW CONTRO
L—This 24
v
control permits both motors to
be operated from a single switch, which is eq
u
ipped with two sets of UP-OFF-
DOWN b
u
ttons.
24v MULTIPLE STATION CONTRO
L—Separate three-b
u
tton UP-STOP-
DOWN switches for each motor, stop at any point desired, operate in any
seq
u
ence.
KEY OPERATED SWITCHIN
G—Two kinds of key-operated switches are
optionally a
v
ailable with this
u
nit.
➀
The key-operated power s
u
pply switch controls power to the screen or
masking and switches. When it is “off”, the switches will not operate
screen. Key may be remo
v
ed from the switch in either “on” or “off”
position.
➁
The three-position key switch permits the screen or masking to be
operated directly by key. In this case, the screen’s operator m
u
st always
ha
v
e a key.
Motor roller
assem
b
ly
Retaining
clip
W
asher
Idler end roller
mounting
b
racket
mo
u
nting bracket. Place washer o
v
er pin and fasten retaining clip in the
groo
v
e of idler pin.
Connect the electrical pl
u
gs from the motors to the mating sockets on the
j
u
nction boxes.
Reinstall the bottom access panel as pre
v
io
u
sly described.
www
.draperinc.com
(765) 9
8
7-7999
