background image

6. Identification and Unpacking

Please visit 

drapertools.com for our full range of accessories and consumables.

EN

– 9 –

– 8 –

EN

1 

Fig.

3 

Fig.

4 

Fig.

2 

Fig.

Important: Read and understand all the safety 

instructions listed in this manual before attempting  

to assemble this product.

Important: Ensure all bolts are only FINGER TIGHT until 

assembly is complete. Then tighten all fixtures securely. 

7.1 Assemble the Legs

7.2 Attach the Top Frames

1.   Place the rear 

left leg (C) on your left and the front 

left leg (A) on your right so that the indented sides are 

at the bottom and facing 

towards you.

 

 Important:  The folding brace should also be facing 

towards you.

2.   Open the folding brace (7) and the diagonal brace  

(8) and align them with the hole halfway up the left 

front leg. 

 Important: The leg should be positioned between the 

two braces, with the lipped edges of the braces facing 

upward. The folding leg should be able to fold upward.

3.  Pass an M8 x 45mm half-thread hex bolt (N) through 

both braces and the leg and secure them in place 

with an M8 nylon-insert lock nut (S).

 

 Important: Place an M8 washer (Q) between each 

brace and the leg to ensure smooth folding.

4.   Attach a foot (M) to the indented end of each leg so 

that the longest edge is positioned outwardly on the 

same side as the folding brace.

5.   Repeat these steps for the front right (B) and rear right 

(D) legs, with the rear leg on your 

left and the front 

leg on your 

right.

6.   Insert the upper ends of the 

left leg assembly 

between the brackets of a top frame (I) so that the 

holes align and the crank handle (2) is positioned 

above the front leg (A).

7.   Pass two M8 x 45mm half-thread hex bolts (N) each 

through an M8 washer (Q) and top frame bracket 

around the leg and secure each in place with another 

M8 washer and an M8 nylon-insert lock nut (S).

8.   Repeat these steps for the right leg assembly, 

ensuring that the crank handle is positioned over  

the 

front leg.

7. Assembly Instructions

6.3 Packaging

Keep the product packaging for the duration of the 

warranty period for reference should the product need to 

be returned for repair.

WARNING! Keep packaging materials out of reach  

of children. Dispose of packaging correctly and 

responsibly and in accordance with local regulations.

(A)  1 x Front left leg

(B)  1 x Front right leg

(C)  1 x Rear left leg

(D)  1 x Rear right leg

(E)  1 x Front crossbar

(F)  1 x Rear crossbar

(G)  1 x Front benchtop

(H)  1 x Rear benchtop

(I) 

2 x Top frames

(J)  2 x U-brackets (bare)

(K)  2 x U-brackets with guide plates

(L)  4 x Clamp blocks

(M)  4 x Feet

(N)  6 x M8 x 45mm half-thread hex bolts

(O)  8 x M6 x 37mm half-thread screws

(P)  16 x M5 x 16mm self-tapping screws

(Q)  12 x M8 washers

(R)  8 x M6 washers

(S)  6 x M8 nylon-insert lock nuts

(T)  8 x M6 nylon-insert lock nuts

(U)  1 x Spanner tool

 

U1.  M8 spanner

 

U2.  M6 spanner

6.2 What’s in the Box?

Carefully remove the product from the packaging and 

examine it for any signs of damage that may have 

occurred during shipment.

Before assembling the product, lay the contents out and 

check them against the parts shown below. If any part is 

damaged or missing, do not attempt to use the product. 

Please contact the Draper Tools Helpline; contact details 

can be found at the back of this manual.

(D)

(C)

(A)

(U2)

(U)

(O)

(U1)

(I)

(H)

(A)

(C)

(A)

(G)

(M)

(I)

(F)

(E)

(L)

(M) (J)

(K)

(B)

(P)

(T)

(S)

(Q)

(N)

(R)

(C)

(I)

(N)

(Q, S)

(N)

(S)

(Q)

Содержание 77020










Отзывы: