manualshive.com logo in svg

Draper 67044, Инструкция по эксплуатации, Страница: 7 / 12

Поделиться
Скачать
Draper 67044 Скачать руководство пользователя страница 7

- 6 -

OPERATION & USE

NOTE: Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.

REMOVING THE BASE (Fig.2.):

Loosen the clamping lever 

✪✌

to remove the base.

NOTE: When refitting the base, ensure the on/off
switch is positioned the same side as the chip
guard.

INSERTING THE BITS (Fig.3 & 4.):

NOTE: Only use cutters of the correct shank
diameter and which are suitable for the speed of
the tool.

With the base removed, press the spindle lock 

✫✌

.

Unscrew the spindle nut 

✬✌

and remove. Choose

from the three collets provided, the appropriate
size for the cutters shank 

1

⁄

4

", 6mm and 8mm. If the

size is not known insert the bit into the collet. The
collect which offers a machine fit  to the bit is the
correct one to use. Do 

NOT

force the bit into a

collet.

Place the collet into the spindle and loosely
replace the nut. Slide in the bit allowing approx. 5 -
10mm (or follow the bit manufacturers instructions)
over hang and tighten the nut.

NOTE: Do not overtighten the nut.

WARNING: Take care when handling the cutter bits
as they are extremely sharp.

Fig.2.

✪✌

Fig.3.

✫✌

✬✌

Fig.4.

Cutter shown not supplied.

5-10mm

Содержание 67044













Отзывы:

Нет отзывов