background image

- 7 -

MAINTENANCE AND PARTS
REPLACEMENT

Regular inspection and cleaning reduces the necessity for maintenance operations and will keep
your tool in good working condition. The tool bearings and gears are life-long lubricated, however
it is advised to check the condition of the grease in the head every 100 hours, if necessary replace
the grease. The motor must be correctly ventilated during tool operation. For this reason avoid
blocking the air inlets with hands. After use disconnect the tool from the power supply and clean
carefully, use compressed air through ventilation slots.

DISPOSAL

At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to the standard regulations of the country in which it is being used, and that
the disposal operation is carried out by specialized personnel following authorized guidelines. In
all circumstances:

– Do not abandon in the environment;

– Do not dispose of together with solid urban waste products;

– Contact the special recycling centres.

WARNING – Disconnect the plug from the power supply socket before replacing any parts.

BRUSHES

The brushes must be replaced after approximately 150-200 working hours, or if they are less than
5-6mm in length.

WARNING – For correct tool operation always change the brushes in pairs, not separately.
The use of original Draper Tool spare parts is recommended. After having fitted new
brushes run the motor for at least five minutes without load for the brushes to bed in.

IMPORTANT – This operation should only be performed by an authorized person.

REPLACING THE POWER SUPPLY CABLE

Check that the power supply cable is in good condition, if not have it replaced by an authorized
person.

Содержание 57848













Отзывы: