Ceiling Mounting
1.
Attach two Sliding Wall Brackets to Ceiling Brackets using .250-20 x ¾"
(19mm)
Cross Head Machine Screws and .250-20 Nylon Inserted Hex Zinc Locking
Nut
(provided)
.
2.
Mount two Ceiling Brackets to the mounting surface. Brackets should be
located at joists. Installer must insure that fasteners used are of adequate
strength and suitable for the mounting surface chosen.
Please Note:
Sliding Brackets can be mounted so they can be located at any
point along the Case Attachment Brackets
(within 24" (61cm) of each end of case)
.
They must be mounted level, and with bottom edges in alignment.
3.
Place front brackets on screen case, making sure the lower curled edge
engages the screen case
(Fig. 1)
.
4.
To protect the screen from damage, place the screen case on clean, steady
surface with the bottom of the screen case facing down.
5.
Remove the bottom screw from each endcap
(Fig. 2)
.
6.
Lift one end of screen case to attach Case Attachment Brackets to screen
case by re-using endcap screws. Also use provided 10-32 x ½"
(13mm)
Cross
Head Zinc Machine Screws, attaching through the wall mounting holes on the
endcaps
(Fig. 2)
.
Please Note:
Make sure to hook bottom of Case Attachment Bracket under
the bottom of the screen case
(Fig. 1)
.
7.
Attach Case Attachment Brackets to front brackets using 10-32 x ½"
(13mm)
Cross Head Zinc Machine Screws
(provided)
.
Wall Mounting
1.
Mount two Sliding Wall Brackets to the mounting surface.
Brackets should be placed on studs. Installer must insure that
fasteners used are of adequate strength and suitable for the
mounting surface chosen.
Please Note:
Sliding Wall Brackets can be mounted so they can
be located at any point along the Case Attachment Brackets
(within 24" (61cm) of each end of case)
. They must be mounted level,
and with bottom edges in alignment.
2.
Place front brackets on screen case, making sure the lower
curled edge engages the screen case
(Fig. 1)
.
3.
To protect the screen from damage, place the screen case
on clean, steady surface with the bottom of the screen case
facing down.
4.
Remove the bottom screw from each endcap
(Fig. 2)
.
5.
Lift one end of screen case to attach Case Attachment Brackets
to screen case by re-using endcap screws. Also use provided
10-32 x ½" Cross Head Zinc Machine Screws, attaching through
the wall mounting holes on the endcaps
(Fig. 2)
.
Please Note:
Make sure to hook bottom of Case Attachment
Bracket under the bottom of the screen case
(Fig. 1)
.
6.
Attach Case Attachment Brackets to front brackets using
10-32 x ½"
(13mm)
Cross Head Zinc Machine Screws
(provided)
.
7.
Mount screen case to wall brackets by slightly angling the upper
slots on the Case attachment Brackets into the upper channel on
the Sliding Wall Brackets, then rotating screen case into place
(Fig. 3)
.
8.
Once the screen is placed in the desired position, secure screen
case to Sliding Wall Brackets using #10-32 x 1"
(25mm)
Cross
Head Screws
(provided)
(Fig. 3)
.
8.
Mount screen case to wall brackets by slightly angling the upper slots on the
Case Attachment Brackets into the upper channel on the Sliding Wall Brackets,
then rotating screen case into place
(Fig. 4)
.
9.
Once the screen is placed in the desired position, secure screen case to Sliding
Wall Brackets using #10-32 x 1"
(25mm)
Cross Head Screws
(provided)
(Fig. 4)
.
Figure 1
Figure 3
Figure 4
Figure 2
page 3 of 4
Floating Mounting Bracket
