DRAKE DSE24A Скачать руководство пользователя страница 16

17

937.746.4556 | 

www.rldrake.com

TS Bitrate:

 User must enter in the bitrate for the output TS. Options are 19.39 Mbps, 38.8 Mbps (default) and 

Custom. The Custom TS bitrate can be set from a minimum of the sum of the video and audio bitrates plus TS 

overhead to a maximum of 38.81070 Mbps. An error message (shown below) will be displayed if the TS bitrate 

entered does not support the configured audio/video bitrates.

“Error!  The total configured Audio/Video bitrates (including TS overhead) exceeds the selected TS bitrate”

  

Modulation Mode:

 allows the user to select the modulation mode. Options are: Reserved, Analog, QAM64, 

QAM256, 8-VSB, and 16-VSB.

Out of Band: 

An out-of-band (OOB) is a channel which is the combination of the forward and reverse OOB 

channels.  When a cable virtual channel is flagged as being out-of-band, it is carried on the out-of-band channel. 

Options  are Enable and Disable. When Enabled, assigns the OOB bit in the TS packet and labels the TS as out-of-

band.

NOTE:

 As per the ATSC and Cable standards, the Modulation Mode and Out-of-Band fields are 

required to be assigned in the TS packet. Selecting the above two fields would allow the TS packets to 

be compliant with industry standards, but would not affect the input or output configuration of the unit.

In the section entitled 

“Output Mapping”

, the user can select and configure the following parameters for the output 

TS indicated by 

“TS - QAM”

 under gray header:

Input:

 indicates the program selected by the user. It includes the Input video source, and audio source.

PID:

 user must enter the PID value for each stream. PID (Packet Identifier) values are embedded by the content 

provider in the MPEG-2 stream to identify tables and programming packets.

Program Number:

 user must enter an output program number. The PMT (Program Map Table) provides 

information for program present in the transport stream such as program_number, and the list of the elementary 

streams (audio, video or data). The range is 1 to 65535.

Short Name:

 user must enter the short name of the channel.  Up to 7 alphanumeric characters are allowed.

Major Channel:

 user must enter the major channel number for the output program. The range is 1 to 99 for 

Terrestrial and 1 to 999 for Cable.

Minor Channel:

 user may enter minor channel number for the output program. The range is 1 to 99 for Terrestrial 

and 0 to 999 for cable. NOTE: When zero (0) is entered as a minor channel, it sets the encoder to provide a one 

part virtual channel number as entered in the major channel field. For example, a major channel of “205” with a 

minor channel of “0” will be displayed as “205” on a TV. A major channel of “205” with a minor channel of “1” will 

be displayed on a TV as “205-1”.

Unit Configuration

Main Tab: TS Configuration Screen

 (continued)

The PID value must be unique in an output stream. If a duplicate PID exists, assign a different PID 

in the range of 48 to 8176 (recommended range provided by the International Standards)

2

3

4

5
6

7

8

9

10

Remember to click on the SAVE button to apply the new values/configurations.

Содержание DSE24A





























Отзывы: