background image

    1. Unpacking and Checking Equipment 

       

Carefully unpack the equipment and its accessories.   

 

1). Remote controller 
2). Base communication module 
3). Main controller 
4). kinds of Harness Assembly 
5). Shock sensor 
 
 

2. Operation Instructions

2-1. ARMING 

The car alarm system checks the intrusion into the car in the arm mode 

        (shock & door open) and pages it the remote controller, and then, it alerts 

        for 45 seconds with siren and light flashing. After alarm, it returns 

        to arm mode. 

2-1-1.    Pressing the “LOCK” button : Press “LOCK” button shortly, and the   

Car locks the door and goes into arm mode with audible chirp and 

visual light flashing. The LED of communication module will be turned on 

for 5 seconds ( ARM delay mode ) and then start flashing ( ARM mode ). 

The remote controller shows green LED flashing and sounds one short beep. 

If you press the “LOCK” button under “NO CHIRP MODE”, the car acts 

the same way above, but without chirp. 

2-1-2.    Automatic passive arming ( When the car is set to passive arming ) : 

When the key is pulled out of key box and all doors are closed,   

the system will arm automatically after 30 seconds. When the car is armed,   

it acts like above procedures. 

 

Note    1: Passive arming is selectable feature that can be turned ON or OFF 

    by your alarm dealer / installer. Please check the installation guide. 

 

 

2-1-3.    Special functions when entering into arming : When the door is opened 

and the “LOCK” button is pressed, the car alerts 4 chirps & 4 light  

flashing.  

When the shock sensor is triggering and the “LOCK” button is pressed, the car 

alerts 3 chirps & 3 light flashing. The car does not alert this status even though it 

is in arm mode, but , if the door is closed and opened again or if the shock sensor 

is muted and triggered again, the car sends alarm signal. 

 

 

2-2. DISARMING 

2-2-1. Pressing the button “UNLOCK” shortly disarms the car. 

                When the car is disarmed, it unlocks the door with two audible chirps and   

visual light flashing. The remote controller shows green LED flashing and   

sounds short beeps two times. If you press the “UNLOCK” button under 

Содержание DTH-3002R











Отзывы: