manualshive.com logo in svg

Dragon Wholesaling DFD30, Руководство по эксплуатации, Страница: 11 / 27

Поделиться
Скачать
Dragon Wholesaling DFD30 Скачать руководство пользователя страница 11

Ultrasonic Flaw Detector                                                                                                                                                        DFD30 

 

11 

Fine adjustment: +1 or -1mm 

Under RANGE, press down key. Right now, there are two tri-angle appear. Under this condition, press + or – key to 

realize fine adjustment. 

 

5.1.2 db-STEP 

Press left or right key to enter into BASE SETTING, then press up or down key to choose db-STEP. 

Press + or – key to change from 01db, 02db, 06db and 12db. 

 

5.1.3 MVTEL 

Users are allowed to set the transmission velocity of ultrasonic wave in workpiece. There are two velocities stored in 

main unit. They are: 

3,240m/s   

    0.127 in /µs  

    Sound velocity of transverse wave in steel 

5,920m/s   

    0.233 in /µs  

    Sound velocity of longitudinal wave in steel 

Usera are also allowed to carry our fine adjustment. 

Under MVTEL, press down key. Right now, there are two tri-angle appear. Under this condition, press + or – key to 

realize fine adjustment. 

Fine adjustment: Step is  1m/s   0.0001in/µs 

 

 

5.1.4 D-DELAY 

Users  could  set  the  pulse  shift  during  detection,  via.  D  delay.  By  which,  users  are  allowed  to  adjust  the  starting 

position  for  waveform, as well  as  adjusting the zero point  of  pulse, so as  to make sure that it is at  the surface or a 

starting face inside the workpiece. If the pulse has to be started from the surface of workpiece, D delay must be set to 

0. 

Range:    0-512mm   

Step: 

      1mm 

There are two ways of adjustment, Rough and fine. 

Rough adjustment 

Under D-DISPLAY menu, press down key. Right now, there are two tri-angle appear. Under this condition, press + or 

– key to realize rough adjustment. 

Fine adjustment 

Under D-DISPLAY menu, press + or – key directly to realize fine adjustment. 

 

5.1.5 P-ZERO 

Range:    0-9.99µs 

Step: 

    0.1µs   

There are two ways of adjustment, Rough and fine. 

Rough adjustment 

Under D-DISPLAY menu, press down key. Right now, there are two tri-angle appear. Under this condition, press + or 

– key to realize rough adjustment. 

Содержание DFD30




























Отзывы:

Нет отзывов