background image

 

14 

DR

 4 -Ton WOOD SPLITTER Safety & Operating Instructions

 

Operating the DR 4 -Ton WOOD SPLITTER 

Note 1

:

 For your added safety, this is a TWO HANDED OPERATION wood 

splitter. The hydraulic control is a single handle valve called the Operating 
Handle. The ram travels forward only while the Operating Handle is held 
down and Electric Motor Start Button is depressed. The cylinder 
automatically completes the return stroke when the Operating Handle is 
released and Electric Motor Start Button is released. 

Note 2: 

Before starting the splitting operation, the log ram should be cycled 3 to 4 
times back and forth (with the Air Bleed Screw open) to help remove any air 
that may have mixed into the hydraulic fluid from shipping and handling. See 
Step 3 on page 11 for the Air Bleed Screw Operation. 

Tip:

 In cold weather, cycling the ram a few times will also warm the hydraulic fluid 

which will allow you to split wood with full power from your machine. 

1.  With a log properly loaded, and with the Air Bleed Screw open, depress the Electric 

Motor Start Button with your right hand and wait a few seconds as the motor 
creates pressure in the hydraulic pump. 

2.  When safe to do so, push down on the Operating Handle. The ram will now 

compress the log against the wedge, splitting the log. 

3.  Keep holding the Operating Handle down until the split pieces of the log fall away. 

When you have finished splitting a log, first release the Electric Motor Start Button 

and then

 release the Operator Handle. This will cause the ram to retract to its start 

position. 

 
 
 
 
 

4.  Make sure nothing will interfere with the ram while it retracts. 
5.  Stack the split wood as you work. This will provide a safer work area by keeping it 

uncluttered; avoiding the danger of tripping or damaging the power cord.  

 

WARNING!

 

If the log does not split immediately, do not continue the

forward thrust of the ram for more than 5 seconds. To do so
can damage the splitter. After the ram has retracted try

repositioning the log on the splitter or set the log aside.

 

Содержание 4-TON ELECTRIC WOOD SPLITTER

































Отзывы: