Front Panel:
Rear Panel:
1
2
3
4
5
6
7
8
9
10
11
SPEAKER OUTPUT
C L A
S S 2 W I R I N G
4 OHM
8 OHM
I N P U T P O W E R
U S E O N
L Y 1 O U T P U T
A T A T I M E
R I S K O F E L E C T R I C A L S H O C
K
D O N O T O P E N
R I S Q U E D E C H O C E L E C T R I Q U E
N E
P AS O U V R I
R
CAUTION
AVIS
FUSE
DA TE OF MFG:
F 1AMP 250V
1 2 0 V
~
6 0 H z 6 5
W
16 OHM
FOOT SWITCH
SEND
RETURN
EQ
BY-PASS
- AMP
®
S E R I A L N O
.
M O D E L # Z A - 3 2
PENTODE TRIODE
C L AS S 1 W I R I N G
12
13
14
15
16
17
18
19
20
1.
Input:
Input jack for your guitar. Hi is for normal use. LO has 3 dB less gain. Use LO with Humbucker equipped
guitars for a cleaner sound.
2. Volume:
Controls overall gain. Set over half way for over-driven sounds. Set below half way for cleaner sounds.
3. Treble:
Controls overall high frequency response.
4. Mid:
Controls overall mid frequency response.
5. Bass:
Controls overall low frequency response.
6. Reverb:
Turn clockwise to add reverb.
7. Cut:
Controls overall tone/presence of amp. Turn clockwise for chime.
8. Mater:
Controls overall amp volume and output tube compression.
9. Stand-By:
Leave in off position for 1 minute when powering up the amp. Turn on for play. Place in off position
for extended break periods.
10. Power:
Switch up to turn on amplifier. Switch down to turn off amplifier.
11.
Power Indicator:
Lights up when power is switched on. If bulb fails replace with type T47.
12.
EQ bypass footswitch jack:
Plug supplied single button footswitch in here. This will enable you to engage the
EQ bypass/gain boost mode. The new variable boost footswitch features an added knob to control the amount of
boost. Simply turn this knob clockwise to increase the amount of boost.
13. Send Jack:
Plug “In” effects here.
14. Send Jack:
Plug “Out” here.
15. 4 OHM Speaker Jack:
Plug in 4 ohm speaker here. Always have a speaker plugged into the amp when it is
powered on. Always match the speaker impedance to the proper speaker out jack. This will allow the amp to sound
its best and avoid damage.
16. 8 OHM Speaker Jack:
Plug in 8 ohm speaker here. Always have a speaker plugged into the amp when it is
powered on. Always match the speaker impedance to the proper speaker out jack. This will allow the amp to sound
its best and avoid damage.
17. 16 OHM Speaker Jack:
Plug in 16 ohm speaker here. Always have a speaker plugged into the amp when it is
powered on. Always match the speaker impedance to the proper speaker out jack. This will allow the amp to sound
its best and avoid damage.
18. Pentode/Triode Switch:
This switch will change how the power tube is configured; in pentode all 5 elements
are used, in triode 3 elements are used. Triode will lower the headroom and change the tonal characteristics and
response.
Note that this does not drop volume by 50% but will decrease the volume overall.
19. Fuse:
The fuse protects the amp from electrical faults. Replace only with the same rating and type stated below
fuse holder (1.5A 250v SLO BLO). If the amp repeatedly blows the fuse contact your dealer or Dr Z Amps.
20. AC Inlet:
(Class I Wiring). This device is used for disconnection from power mains and must remain readily
opearable. The power indicator light does not indicate connection to power mains. The power cord must be
disconnected to disconnect amplifier from power mains.
