background image

CONTACT US AT 

www.DRpower.com

          13

 

Hands on 
Sides of Wood 

Figure 23 

Wood 
Against 
Wedge 

Splitting

 

Note:

  All logs should be no longer than 24". Use the following photos for the correct 

and incorrect methods of splitting logs. Never split a log using an incorrect or 
unsafe method. 

1.

 

Place the log on the Log Splitter. Grasp the log on the sides near the middle 
of the block (

Figure 23

). Center the log, side-to-side, on the rail of the Log 

Splitter, making sure that one end is against the Splitting Wedge. 

Figure 20 

 

Do not place your hands on the ends of the log when loading the Log 
Splitter. This is a very UNSAFE method and could result in injury to your 
hands (

Figure 20

). 

 

Do not reach or step across the beam while the Log Splitter is running. 
This is a very UNSAFE method which could cause personal injury or even 
death. 

Figure 21 

Figure 22 

The engagement Handle must be held fully forward against the hard stop 
when splitting.  Failure to do so may result in kickback of the Handle. 

 

Never attempt to split wood across the grain. The Log Splitter was not 
designed for cross-grain splitting. Doing so could damage the Log 
Splitter and may cause personal injury (

Figure 21

). 

 

Make sure both ends of the log you are splitting are cut as square as 
possible. This will prevent the log from sliding out of position while under 
pressure (

Figure 22

). 

THE RAPIDFIRE LOG SPLITTER OPERATES DIFFERENTLY THAN A 
HYDRAULIC SPLITTER.  NOT OPERATING THE MACHINE PROPERLY WILL 
RESULT IN DAMAGE TO THE MACHINE.  ALWAYS FOLLOW THESE 
NOTICES: 

 

Do not be timid.  A rapid movement of the Engagement Handle is 
necessary for the Rack and Pinion to engage and disengage fully without 
damage. 

 

The Engagement Handle should never be stopped in any location 
between the fully forward or fully backward positions. 

 

Do not hold the Handle in the forward position when the Ram stops 
moving forward.  Always pull the Engagement Handle RAPIDLY to the 
back (Auto-Retract) position as soon as the Log is split or when the Ram 
is at the end of the stroke or when the Ram stops moving forward due to 
a tough log. 

Содержание RapidFire Pro

































Отзывы: