background image

Pool Heat Pump _23

PRODUCT WARRANTY

DPL

heat pumps are warranted against material and manufacturing defects for a period of one (1) year, including parts

and labour. The compressor is also warranted for a period of one (1) year.

The warranty period is deemed to start on the installation date and the limited warranty plan form must be sent within sixty
days following the installation.

DPL

is not responsible for:

> Normal maintenance.
> Damage or repairs required as a consequence of faulty installation or application by others. 
> Failure to start due to voltage conditions, blown fuses, open circuit breakers, or other damage due to the 

inadequacy or interruption of electrical service. 

> Damage or repairs needed as a consequence of any misapplication, abuse, improper servicing, unauthorized

alteration, or improper operation. 

> Damage as a result of flooding, wind, fire, lightning, accidents, corrosive atmospheres, or other conditions 

beyond the control of 

DPL

> Parts not supplied or approved by 

DPL

> Products installed outside the United States or Canada.
> Any damages to persons or property of whatever kind, direct or indirect, special or consequential, whether 

resulting from use or loss of use of the product. 

LIMITATION OF WARRANTIES

This warranty is exclusive and in lieu of any implied warranties of merchantability and fitness for a particular purpose and
all other warranties express or implied. The remedies provided for in this warranty are exclusive and shall constitute the
only liabilities on the part of DPL including any statements made by any individual, which shall be of no effect. 

HOW TO OBTAIN SERVICE

Heat pump servicing is managed by our Service Centre. Your warranty may be voided if servicing is not provided by one
of our service representatives.

Prior to requesting assistance or servicing, read the 

TROUBLESHOOTING

section. This might save you the cost of a service call.

If you are unable to solve your problem and need help, contact our Service Centre at +1.450.818.4758.

DPL POOL EQUIPMENT, INC.

43, de l’Alcazar - Blainville 

(Québec) Canada J7C 1R4

Содержание 100 HPRA-410



























Отзывы: