background image

 

Roof Mount Installation Guide 

V1.3 

Page 2 of 13 
 
Please download the latest version of this document from 

www.dpasolar.com.au/support

 prior to commencing installation. 

Under no circumstances shall DPA Solar be liable for special, indirect or consequential damages arising out of use of this product. 

 

Introduction 

 

DPA Solar racking when installed in accordance with this guide and applicable building 
regulations will be structurally adequate and meet the requirements of AS/NZS1170.  
 

 

 

 
 

 
It is important to note that the installer is responsible for the following:

 

  Complying with all applicable local or national building codes, including any that may 

supersede this manual; 

  Complying with all electrical, health and safety and other applicable regulations as 

applicable to the location; 

  Ensuring that DPA Solar racking and other products are appropriate for the particular 

installation and the installation environment;  

  Ensuring that the roof, its rafters, connections, and other structural support members can 

support the array under building live load conditions;  

  Ensuring that all screws and fixings have adequate pullout strength and shear capacities 

as installed;  

  Ensuring that loads other than wind are considered in the design.  This document 

addresses only wind loads on the assumption that wind produces the maximum load 
factor affecting an installation. Verify that other local factors, such as snow loads and 
earth quake effects, do not exceed the wind loads.  

  Maintaining the waterproof integrity of the roof, including selection of appropriate 

flashing;  

  Fitting galvanic isolation where required to protect against dissimilar metals corrosion; 

and  

  Ensuring safe installation of all electrical aspects of the PV array.  

 

This product is Warranted to be free from defective material and workmanship for a period of 10 
years.  Please visit www.dpasolar.com.au/support

 

for full warranty details. 

 

Содержание Roof Mount














Отзывы: