DP Pumps Hydro-Unit Premium Скачать руководство пользователя страница 14

Страница: 14 / 96

14 / 96

3 Transport/Storage/Disposal

3.1 Checking the condition upon delivery

1. On transfer of goods, check each packaging unit for damage.

2. In the event of in-transit damage, assess the exact damage, document it and notify DP

or the supplying dealer and the insurer about the damage in writing immediately.

3.2 Transport

DANGER

Pressure booster system tipping over

Danger to life from falling pressure booster system!

Never suspend the pressure booster system by its power cable.

Do not lift the pressure booster system by its manifold.

Observe the applicable local accident prevention regulations.

Observe the information on weights, centre of gravity and fastening points.

Use suitable and permitted transport equipment, e.g. crane, forklift or pallet
jack.

Transport equipment / lifting equipment suitable for the corresponding weight has been
selected and is on hand.

1. Remove the packaging. Remove the caps from the connection openings.

2. Check for any in-transit damage.

3. Transport the pressure booster system to the place of installation.

4. Detach the pressure booster system from the pallet using a suitable tool.

5. Separate the pressure booster system from the wooden skids with a suitable tool. Lift

the pressure booster system off. Dispose of the wooden skids.

6. Carefully place down the pressure booster system at the site of installation.

3.3 Storage/preservation

CAUTION

Damage during storage due to frost, moisture, dirt, UV radiation or
vermin

Corrosion/contamination of pressure booster system!

Store the pressure booster system in a frost-proof room. Do not store
outdoors.

CAUTION

Wet, contaminated or damaged openings and connections

Leakage or damage of the pressure booster system!

Only open the openings of the pressure booster system at the time of
installation.

If commissioning is to take place some time after delivery, we recommend that the following
measures be taken:

Store the pressure booster system in a dry, protected room where the atmospheric humidity
is as constant as possible.

Содержание Hydro-Unit Premium

































































































Результаты поиска

Содержание Hydro-Unit Premium

Отзывы:

Похожие инструкции для Hydro-Unit Premium

Бренды по названию

Популярные бренды

DP Pumps Hydro-Unit Premium, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Hydro-Unit Premium

Отзывы:

Похожие инструкции для Hydro-Unit Premium

Бренды по названию

Популярные бренды