manualshive.com logo in svg

Dover PSG Wilden PS1500, Руководство пользователя

Поделиться
Скачать
Dover PSG Wilden PS1500 Скачать руководство пользователя страница 9

 

WIL-13001-E-01  

9 

ALLOY C PUMPS 

 

SECTION 5 

 

PS400 ALLOY C 
RUBBER-FITTED

 

 

Ship Weight………….…Alloy C 45 kg (100 lb) 

Air Inlet……………………………………….3/4" 

Inlet……………………………...38 mm (1-1/2") 

Outlet……………………………38 mm (1-1/2") 

Suction Lift………………..…..6.7 m Dry (22.1

′

) 

8.6 m Wet (28.4

′

) 

Disp. per Stroke

1

……………....1.0 L (0.26 gal) 

Max. Flow Rate……………..271 lpm (72 gpm) 

Max. Size Solids……………….4.8 mm (3/16") 

 
 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 197 lpm (52 gpm) against 

a discharge head of 1.4 bar (20 psig) requires 

4.1 bar (60 psig) and 54 Nm

3

/h (32 scfm) air 

consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

 

 

PS400 ALLOY C  
FULL-STROKE  

PTFE-FITTED 

 

Ship Weight………….…Alloy C 45 kg (100 lb) 

Air Inlet……………………………………….3/4" 

Inlet……………………………...38 mm (1-1/2") 

Outlet……………………………38 mm (1-1/2") 

Suction Lift………………..…..6.7 m Dry (22.1

′

) 

8.6 m Wet (28.4

′

) 

Disp. per Stroke

1

……………....0.9 L (0.25 gal) 

Max. Flow Rate……………..348 lpm (92 gpm) 

Max. Size Solids……………….4.8 mm (3/16") 

 
 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 238 lpm (63 gpm) against 

a discharge head of 2.1 bar (30 psig) requires 

5.5 bar (80 psig) and 78 Nm

3

/h (46 scfm) air 

consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

 

 

 

PERFORMANCE 

Содержание PSG Wilden PS1500

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды