Dover PSG ALL-FLO IOM A050 Series Скачать руководство пользователя страница 21

Страница: 21 / 23

ALF-11030-E-02

All-Flo

ELASTOMERS

WETTED ELASTOMERS

FKM

is an elastomer with good corrosion resistance to a

wide variety of chemicals. Temperature range -40°F

to 350°F (-40°C to 177°C).

Most of the above elastomers are available in FDA

approved formulations.

BUNA-N (NITRILE)

is a general purpose elastomer used with water and

many oils. Temperature range 10°F to 180°F (-12°C

to 82°C).

GEOLAST®

is an injection molded thermoplastic material with

characteristics similar to Nitrile. Has excellent

abrasion resistance. Temperature range 10°F to 180°F

(-12°C to 82°C).

EPDM

is a general purpose elastomer with good resistance

to many acids and bases. Temperature range -40°F

to 280°F (-40°C to 138°C).

SANTOPRENE®

is an injection molded material with characteristics

similar to EPDM. Has excellent abrasion resistance.

Temperature range -40°F to 225°F (-40°C to 107°C).

PTFE (POLYTETRAFLUOROETHYLENE)

is a thermoplastic polymer that is inert to most

chemicals. Temperature range 40°F to 220°F (4°C to

104°C).

Geolast

is a registered trademark of ExxonMobil Chemical Co.

Santoprene

is a registered trademark of ExxonMobil Chemical Co.

Hytrel

is a registered trademark of DuPont Performance Elastomers L.L.C.

Magnalube

is a registered trademark of Carleton-Stuart Corp.

SECTION

Содержание PSG ALL-FLO IOM A050 Series
























Результаты поиска

Содержание PSG ALL-FLO IOM A050 Series

Отзывы:

Бренды по названию

Популярные бренды

Dover PSG ALL-FLO IOM A050 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PSG ALL-FLO IOM A050 Series

Отзывы:

Бренды по названию

Популярные бренды