Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 64

Страница: 64 / 136

Issued May 2020
Lift Arm

Printed in the U.S.A.

Lift Arm

REMOVE GRABBER BEAM ASSEMBLY

The grabber beam connects the grabber gears and grabbers to the lift arm. If the beam is damaged, you must replace the
grabber beam. You need the following tools to replace the grabber beam.

A. Tools Required

Quantity

Tool

Personal protective equipment

Socket wrench (3/4” and 9/16”)

Impact wrench (3/4”, 15/16” and 9/16”
sockets)

3/4” JIC plugs and caps for hydraulic fittings

1-1/4” wrench

1-1/8” wrench

10” C-clamp

1-1/2” steel rod

2lb hammer

Plastic ties

B. Replace Grabber Arm

Replacing the grabber beam requires two people. To replace the beam, complete the following steps:

1. Use the 3/4” wrench and the impact wrench with the 3/4” socket to remove the bolts that connect the grabber arm to

the grabber gear assembly.

2. Disconnect the grabber proximity switch cable. Use plastic ties to tie the cable out of the way.

3. Remove grabbers and set aside.

4. Use the impact wrench with the 15/16” socket to remove the retainer plate and the pin retaining bolt. See the figure

below. DO NOT remove the pin yet. You will remove the pin in a later step.

Figure 23. Grabber Beam and Gear Assemblies with

Retainer Plate and Pin Retaining Bolt

Содержание HEIL LIBERTY TP1L-SM-0520










































































































Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию

Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды