Dover H-20905-PA страница 4 Скачать руководство пользователя

Страница: 4 / 24

IMPORTANT:

OPW products should be used in compliance with applicable federal, state, provincial, and local laws and regulations. Product selection should be

based on physical specifications and limitations and compatibility with the environment and materials to be handled. OPW MAKES NO WARRANTY OF FITNESS

FOR A PARTICULAR USE. All illustrations and specifications in this literature are based on the latest product information available at the time of publication. OPW

reserves the right to make changes at any time in prices, materials, specifications and models and to discontinue models without notice or obligation.

Drylok

Dry Disconnect

Coupler and Adaptor Body

Super-Pak

Material

Dust Cap and Plug – included
with system

Size

Connected

3-21/64"

85.6mm

23-

15/32"

62.7mm

5-3/8"

136.5mm

1-7/8"

47.6mm

6-3/4"

171.5mm

4-37/64"

116.3mm

3-33/64"

89.3mm

2-5/32"

54.9mm

3-3/16"

81mm

3-3/4"

95.3mm

6-1/16"

153.9mm

6-3/16"

173mm

127mm

152.4mm

2-3/4"

69.9mm

8-3/8"

212.7mm

7-1/4"

184.2mm

7-7/32"

183.4mm

127mm

4-15/16"

125.4mm

5-5/16"

134.9mm

10-1/6"

258.3mm

7-3/4"

196.9mm

6-3/16"

157.2mm

8-3/4"

222.3mm

101.6mm

12"

304.8mm

8-31/32"

227.8mm

8-49/64"

197.3mm

5-1/2"

139.7mm

6-7/8"

174.6mm

7-17/64"

184.7mm

13-3/8"

339.7mm

Size indicates NPT Pipe Thread

Drylok

Dry Disconnect – Product Specifications

Dimensions

Max Pressure

(psi/bar)

Weight Coupler

(lbs/kg)

Adaptor

(lbs/kg)

Temps PTFE/

FFKM (F / C)

Temps

Fluorocarbon

Temps EPDM

Temps Buna

150 (10 bar)

2.25 (1.0)

1.25 (.6)

0ºF-350ºF

(-18ºC-177ºC)

-20ºF-350ºF

(-29ºC-177ºC)

-40ºF-280ºF

(-40ºC-138ºC)

-40ºF-225ºF

(-40ºC-107ºC)

150 (10 bar)

10.25 (4.6)

7.5 (3.4)

0ºF-350ºF

(-18ºC-177ºC)

-20ºF-350ºF

(-29ºC-177ºC)

-40ºF-280ºF

(-40ºC-138ºC)

-40ºF-225ºF

(-40ºC-107ºC)

150 (10 bar)

14.5 (6.5)

11.75 (5.3)

0ºF-350ºF

(-18ºC-177ºC)

-20ºF-350ºF

(-29ºC-177ºC)

-40ºF-280ºF

(-40ºC-138ºC)

-40ºF-225ºF

(-40ºC-107ºC)

Technical Specification

Содержание H-20905-PA

























Результаты поиска

Содержание H-20905-PA

Отзывы:

Похожие инструкции для H-20905-PA

Бренды по названию

Популярные бренды

Dover H-20905-PA, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание H-20905-PA

Отзывы:

Похожие инструкции для H-20905-PA

Бренды по названию

Популярные бренды