Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 71

Страница: 71 / 363

reset controller-statistics

Description

Resets performance statistics for controllers.
This command resets all controller statistics except Power On Time. To reset this, restart or power

cycle a controller.

Min. role

manage

Syntax

reset controller-statistics

[a|b|both]

Parameters

a|b|both

Optional. Specifies whether to reset statistics for controller A, B, or both. If this parameter is omitted,

statistics are reset for both controllers.

Example

Reset statistics for both controllers.

# reset controller-statistics

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 71 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: