Dot Hill Systems AssuredSAN 6004 Скачать руководство пользователя страница 70

Страница: 70 / 363

Alphabetical list of commands

reset all-statistics

Description

Resets performance statistics for both controllers. You can specify either to reset all live statistics to

zero, or to reset (clear) all historical performance statistics for all disks. If you reset historical statistics,

an event will be logged and new data samples will continue to be stored every quarter hour.

Min. role

manage

Syntax

reset all-statistics

[historical]

[prompt yes|no]

Parameters

historical

Optional. Specifies to reset historical statistics instead of live statistics. If this parameter is omitted, the

command will reset live statistics instead of historical statistics.

prompt yes|no

Optional. For scripting, this specifies an automatic reply to the confirmation prompt that will appear

if the historical parameter is specified:

•

yes

: Allow the command to proceed.

•

: Cancel the command.

If the historical parameter is specified and the prompt parameter is omitted, you must manually reply

to the prompt. If the historical parameter is omitted, the prompt parameter has no effect. There is no

confirmation prompt for live statistics.

Example

Reset all live statistics for both controllers.

# reset all-statistics

Reset all historical disk-performance statistics for both controllers.

# reset all-statistics historical

This command will reset all historical disk statistics.

Do you want to reset? (y/n)

yes

Содержание AssuredSAN 6004












































































































































































































































































































































































Результаты поиска

Содержание AssuredSAN 6004

Отзывы:

Dot Hill Systems AssuredSAN 6004, Справочное руководство CLI, Страница: 70 / 363

Результаты поиска

Содержание AssuredSAN 6004

Отзывы: