Dostmann Electronic OXY 7 Скачать руководство пользователя страница 12

Страница: 12 / 15

OXY 7

9. Parameter settings

During measurement mode press

to enter in the setup menu.

Press

and

keys to scroll setup menu: P5.0→P6.0

P5.0: Settings of the parameter Oxygen

P6.0: Settings of the meter

Press

key to enter in the selected menu and to confirm the changes.

Press

and

keys to scroll the sub-menus and to change the values.

Anytime press

key to exit from setup menu and to return in the measurement mode, the changes

made and confirmed with

key will be saved.

9.1 Setup Menu

Main Menu

During SETUP menu, the instruments cannot be switched off, you first need to exit from SETUP with

key.

Note:

P5.1

Calibration at 0%

P5.2

Salinity compensation

P5.5

Restore factory defaults

P5.6

Calibration of temperature sensor

Sub-menu of parameter Oxygen

P6.1

Temperature measuring unit (°C-°F)

P6.8

Activate / Deactivate auto power-off

Sub-menu of the meter settings

P5.0

P6.0

Содержание OXY 7
















Результаты поиска

Содержание OXY 7

Отзывы:

Бренды по названию

Популярные бренды

Dostmann Electronic OXY 7, Руководство пользователя

Результаты поиска

Содержание OXY 7

Отзывы:

Бренды по названию

Популярные бренды