Dormakaba 9000 Series Скачать руководство пользователя страница 5

dormakaba 9000 Series MLR Installation Instructions

95071186

01-2021

Exit Device

5

MLR x Power Supply x Power Transfer x Input Device

2.2  Single Door: 

F9300 MLR Exit Device x PS610RF Power Supply x ES105 Power Transfer x 

Input Device

Operation: 

Door is locked and secured. Entrance by presenting valid credentials at exterior input device which triggers the PS610RF 

Power Supply to energizes motor of F9300 MLR Exit Device retracting latch botl on 9300 MLR Exit Device for time set on input device 

N.C. relay output. Entrance is also possible by key in rim cylinder of YP03 trim which retracts latch bolt of F9300 MTR Exit Device 

by-passing motorized latch retraction. Egress is always possible by depressing touch  bar of F9300 MLR Exit Device.

Fire Alarm Activation:

 F9300 MLR Exit Device is de-energized releasing latch bolt allowing positive latching when door is closed. 

Immediate egress is possible by depressing touchbar of F9300 MLR Exit Device.

NOTES

:

1. All Wiring and interface between EAC components and to fire alarm panel to be determined and supplied by others.

2. PS610RF Power Supply to be set for 24VDC output.

3. PS610RF Power Supply to be controlled by UL listed fire alarm panel.

4. Input device N.C. relay output unlock time to be determined and set in field by others.

NOTE: This wiring diagram is provided to assist in interfacing 

dormakaba products into the system described above. 

Compatibility and functionality of components not supplied by 

dormakaba are not guaranteed. Component failure resulting from 

improper wiring is not covered by warranty. Refer to individual 

device product information sheets and installation instructions 

for wire guage sizes and additionalinformation.

Minimum Wire Guage Chart (AWG) for 24V AC/DC

Distance in Feet for 2 Conductors from Power 

Source to Locking Device

AMPS

25

50

75

100

150 200

250 300

.25

18

18

18

18

18

18

18

18

.50

18

18

18

18

18

18

18

16

.75

18

18

18

18

18

16

16

14

1.00

18

18

18

18

16

16

14

14

1.50

18

18

18

16

16

14

2.00

18

18

16

16

14

2.50

18

18

16

14

3.00

18

16

14

14

Parts List:

1 EA. - PS610RF Power Supply, Input: 115VAC/60 Hz, 0.8 Amps, Output: 1.0 Amps 

@ 24VDC, regulated and filtered (dormakaba)

1 EA. - F9300 MLR Exit Device, .88 Amp @ 24VDC x YP03 Pull Trim (dormakaba)

1 EA. - ES105 Power Transfer (dormakaba)

1 EA. - Input device (dormakaba)

1 EA. - 8916 S-DS surface door closer (dormakaba)

Содержание 9000 Series











Отзывы: