background image

3 Replacement Procedure

3.1 Unit Preparation

For the upgrade procedure presented in this document, the server (DCP-2000 or DCP-
2K4) unit must be removed from its operating location and put in a clean area (far from 
other devices and on 

a surface fitted with an antistatic mat

) as presented below:

1. Power off the unit by  selecting SHUT DOWN from the LOGOUT menu: "

Menu → 

Logout...

” and select “

Shutdown

".  Any other method might DAMAGE THE RAID 

and result in RAID FAILURE.

2. Unplug the two power cables.

CAUTION

: The unit has a dual redundant power supply. Both power cables have to 

be removed.

Note

: Disconnect any other cables in order to put the unit in a proper place (fitted 

with antistatic setting) for this operation. In this case, you might want to put a 
label to identify each cable you remove to facilitate their re-installation at the 
end of the procedure (e.g. “AES cable”, “GPIO Cable”, …).

3. Remove the server from its rack and place it in a location (e.g. a desk) where you 

have room to perform the procedure, while being grounded according to ESD rules 
presented in ISO 9001 (2000).

4. Remove the lid according to the steps below:

Remove the six screws holding the lid (two on each side and two on the rear 
panel of the chassis) using the Phillips tip screwdriver:

                

                          

(a)

(b)

Figure 3: Lid Screws Locations – (a) DCP-2000, (b) DCP-2K4

 D2K.DP.000804.DRM 

Page 5

 Version 1.0

Doremi Cinema LLC Confidential

CAUTION

:  During the procedure presented in this document, you will have 

to remove screws. 

Collect all removed screws

, as you will have 

to re-use them when putting back the concerned components at 
a later stage of the procedure.

side 

screws

Rear panel screws

Rear panel screws

Side screws

side screws

Содержание DCP-2000












Отзывы: