Doosan Ingersoll Rand 7/20 Скачать руководство пользователя страница 43

Страница: 43 / 78

MAINTENANCE

7/20, P65

1. Main pivot bolt.

2. Securing screw

3. Adjusting screw

4. Airend

DRIVE BELT REPLACEMENT / ADJUSTMENT

WARNING:

DURING THE ADJUSTMENT / REPLACEMENT

PROCEDURE ALWAYS DISCONNECT BATTERY.

Remove drive belt guard.

Loosen securing screw M12 beside and above the Airend.

Loosen main pivot bolt M16.

Disconnect adjusting screw and pivot Airend towards engine to

slacken belt and remove belt from pulleys.

Fit new belt over pulleys, pivot Airend away from engine and

−

engage adjusting screw.

Adjust drive belt tightening by means of adjusting screw with M8

head socket screw.

Adjustment values:

New drive belt

105

−

115 Hz (35N

−

38N/5.9mm)

Run in drive belt

−

98 Hz (25N

−

28N/5.9mm)

Tighten securing screw M12 beside and above the Airend.

Tighten main pivot bolt M16 and secure by lock nut.

Check belt adjustment.

Install drive belt guard.

Содержание Ingersoll Rand 7/20















































































Результаты поиска

Содержание Ingersoll Rand 7/20

Отзывы:

Похожие инструкции для Ingersoll Rand 7/20

Бренды по названию

Популярные бренды

Doosan Ingersoll Rand 7/20, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Ingersoll Rand 7/20

Отзывы:

Похожие инструкции для Ingersoll Rand 7/20

Бренды по названию

Популярные бренды