Doosan 10/105CWJD Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 139

background image

Book: 23227143 (8-24-2010) Rev C

Page 53

COMPRESSOR CODE 52

IQ Filter Restriction

S18 Differential Switch Circuit:

Circuit Description:

The differential pressure switch connects to the WEDGE controller as shown in
the circuit above. S18 has a switch contact that closes when the pressure across
the IQ air filter is restricted. The dark blue WJDe is the sense line to the WEDGE.
The brown WJDe is the switch common to ground.

Component Location:

S18 IQ air filter differential pressure switch is located on a bracket inside the
machine beside the IQ air filter.

Explanation:

The WEDGE has detected a closed switch contact from the IQ air filter S18
differential pressure switch.

Effect:

Code 52 is a SHUTDOWN condition and will stop the machine. The Restricted IQ Air
Filter diagnostic light will be on solid, the Compressor Malfunction light will be on
solid, and Code 52 will be displayed.

«
...
53
54
55
56
57
...
»

Содержание 10/105CWJD












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 10/105CWJD

Бренд: Daewoo Страницы: 14

Бренд: Native Instruments Страницы: 14

Бренд: Kobalt Страницы: 8

Бренд: Kobalt Страницы: 8

Бренд: Parkside Страницы: 72

Бренд: WilTec Страницы: 6

Бренд: Atlas Copco Страницы: 94

PSG Mouvex MX12

Бренд: Dover Страницы: 18

Бренд: HSS Hire Страницы: 2

Бренд: Raider Страницы: 74

Бренд: Zephyr Страницы: 9

Бренд: Ranger Products Страницы: 10

Бренд: Central Pneumatic Страницы: 13

Бренд: Danfoss Страницы: 48

Бренд: Emerson Страницы: 84

Бренд: Emerson Страницы: 29

Бренд: Emerson Страницы: 8

Бренд: Emerson Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды